manualshive.com logo in svg

Axel WOLF 1MS, User Manual, Page: 137 / 229

Share
Download
Axel WOLF 1MS User Manual Download Page 137

TECHNICAL APPENDIX

 

 

 

      | TECHNICAL APPENDIX 

137 

 

16 

TECHNICAL APPENDIX 

The following provides all the technical explanations, the connection pinouts to and from the  Wolf 2MS device. Always 
refer to this technical appendix for the connections and the connection procedures. Should you discover inconsistencies 
between the documentation below and the hardware device, please contact Axel Technology at the numbers and emails 
provided at the end of this manual. Our technical and support department will be happy to help and assist you to the best 
of our ability! 

16.1  APPENDIX A - BALANCED AUDIO AND PINOUT CONNECTION  

Connection diagram Balanced Audio on Balanced

 

XLR

 

for

 

Analog audio 

Input

 and 

Output

 (Left+Right) and 

Input

 and

 

Output

 AES/EBU Digital Audio. 

 

 

 

16.2  APPENDIX B - USB A/B CONNECTION 

 

 

Summary of Contents for WOLF 1MS






































































































































































































































Reviews:

No comments