Avaya P330 Reference Manual Download Page 53 | Manualshive

Page: 53 / 360

background image

Chapter 2 Avaya P330 Layer 2 CLI Commands

Avaya

P330 Reference Guide

35

ping

User level: user, privileged, supervisor

Use the

ping

command to send ICMP echo request packets to another node on the

network.

L

You can use this command via the master switch only.

The syntax for this command is:

ping

[host[number]]

Example: to ping the IP address 149.49.48.1 three times:

prompt-length

User level: privileged, supervisor.

Use the

prompt-length

command to specify the length of the default CLI

prompt.

The syntax for this command is:

prompt-length

<full|<prompt-size>>

host

Host IP address/Internet address of route destination. If missing,
then the host IP address specified in the last ping command is used.

number

Number of packets to send. If missing, then the number specified in
the last ping command is used. If the last number is not available, the
default is 4.

P330-N>

ping

149.49.48.1 3

PING 149.49.48.1: 56 data bytes

64 bytes from 149.49.48.1: icmp_seq=0. time=0. ms

64 bytes from 149.49.48.1: icmp_seq=1. time=0. ms

64 bytes from 149.49.48.1: icmp_seq=2. time=0. ms

----149.49.48.1 PING Statistics----

3 packets transmitted, 3 packets received, 0% packet loss

round-trip (ms) min/avg/max = 0/0/0

full

Display the full length of the prompt

prompt-
size

Set the length in characters of the prompt to display

«
...
51
52
53
54
55
...
»

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

Brand: ABB Pages: 2

Brand: PAC Pages: 20

Touchstone TG1652

Brand: Arris Pages: 44

Brand: HW Group Pages: 19

KNX-GSM Gateway

Brand: B+B Pages: 19

Brand: ADTRAN Pages: 8

Brand: Badger Meter Pages: 24

Brand: IC nexus Pages: 36

SmartNode 4970 Series

Brand: Patton Pages: 8

NetLinx Clear Connect NXB-CCG

Brand: AMX Pages: 3

NetLinx NXB-KNX

Brand: AMX Pages: 2

Brand: Tema Telecomunicazioni Pages: 35

Brand: enphase Pages: 3

Brand: enphase Pages: 6

ENV-S-AM1-230-60

Brand: enphase Pages: 37

Enphase Envoy-S Metered

Brand: enphase Pages: 49

Brand: ATX Pages: 36

Brand: Black Box Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands