Avaya P330 Reference Manual Download Page 38 | Manualshive

Page: 38 / 360

background image

Chapter 2 Avaya P330 Layer 2 CLI Commands

20

Avaya

P330 Reference Guide

copy tftp startup-config

User level: privileged, supervisor.

L

This command applies to the P334T-ML only when it is in “Layer2”

device mode.

Use the

copy tftp startup-config

command to download a policy

configuration from the saved TFTP file to the Startup Configuration file in the
NVRAM.

The syntax for this command is:

copy tftp startup-config <filename> <ip>

Example (for Windows):

Example: (for Unix):

copy tftp SW_image

Use the

copy tftp SW_image

command to download a new firmware software

version into bank B while either keeping the old version in bank A, or downloading
the Embedded Web manager software into bank A.

The syntax for this command is:

copy tftp SW_image <sw_image_file> EW_archive <EmWeb_file>

<IP_addr> <mod_num>

filename

Destination file name in the tftp server (full path)

ip

The ip address of the tftp server.

Router-N (super) #

copy tftp startup-config

c:\p330\startup.cfg 149.49.100.41

Router-N (super) #

copy tftp startup-config /folder/

startup.cfg 149.49.100.41

sw_image_file

Firmware image file name (full path)

EmWeb_file

Embedded Web Manager image file name (full path)
- Optional, can be a dummy name

IP_addr

The ip address of the TFTP server

mod_num

Target switch module number

«
...
36
37
38
39
40
...
»

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

Brand: C-Bus Pages: 36

Brand: Lantronix Pages: 2

Brand: B&B Electronics Pages: 83

Brand: ATCOM Pages: 8

Brand: Advantech Pages: 66

Brand: Inteno Pages: 10

Brand: MediaAccess Pages: 68

Brand: NetComm Pages: 212

Brand: ABB Pages: 20

Brand: Fujitsu Pages: 46

BACnet UTY-VBGX

Brand: Fujitsu Pages: 103

Brand: Fujitsu Pages: 159

SpaceLink WL-500

Brand: Asus Pages: 8

Brand: Dell Pages: 29

Brand: Dell Pages: 40

RB924i-2nD-BT5&BG77

Brand: MikroTik Pages: 16

WIRELESS DATA GATEWAY

Brand: Paradyne Pages: 66

Ixxat SG-gateway

Brand: HMS Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands