Avaya P330 Reference Manual Download Page 309 | Manualshive

Page: 309 / 360

background image

Chapter 4 Load Balancing CLI Commands

Avaya

P330 Reference Guide

291

Example:

real-bridging-fw hc success-retries

User level: privileged, supervisor
Use the

hc success-retries

command to set the number of times the real

bridging firewall should be health-checked before determining success. Use the

no

hc

form of this command to set the success-retries to the default value (1).

The syntax for this command is:

[no] hc success-retries <success-retries>

Example:

real-bridging-fw hc timeout

User level: privileged, supervisor

Use the

hc timeout

command to set the amount of time after which the real

bridging firewall is considered to have "timed out". Use the

no

form of this

command to set the time-out to the default value (1 second).

The syntax for this command is:

[no] hc timeout <time-sec>

Example:

Router-N(configure)#

hc interval 10

success-retries

The number of times, an integer from 1 to 32.

Router-N(configure)#

success-retries 10

time-sec

The amount of time in seconds, an integer.

Router-N(configure)#

hc timeout 10

«
...
307
308
309
310
311
...
»

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

Brand: NetComm Wireless Pages: 28

Brand: Yeastar Technology Pages: 66

Brand: Zennio Pages: 38

Brand: Planet Pages: 57

Brand: Juniper Pages: 3

Brand: QNAP Pages: 168

Brand: Planet Pages: 2

Brand: VBOX Pages: 40

Brand: Perfectone Pages: 39

Brand: Lauda Pages: 24

Brand: Alarm Lock Pages: 8

Brand: Alarm Lock Pages: 8

Brand: ActionTec Pages: 6

Brand: ADTRAN Pages: 34

Brand: 2N Pages: 101

Brand: IDTECK Pages: 65

Brand: Aaeon Pages: 39

intelligent Touch Manager BACnet DCM014A51

Brand: Daikin Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands