Avaya P330 Reference Manual Download Page 70 | Manualshive

Page: 70 / 360

background image

Chapter 2 Avaya P330 Layer 2 CLI Commands

52

Avaya

P330 Reference Guide

Example:
To configure the inband interface on VLAN 1, IP address 1.1.1.1 and netmask
255.255.255.24:

set interface ppp

User level: privileged, supervisor.

Use the

set interface ppp

command to configure the Master agent PPP

interface IP parameters, exit modem mode, disconnect the PPP session, or reset the
connected modem.
You must configure an IP address and net-mask for the P330 before you can
establish a PPP connection. The IP address is a dummy address that is shared
between two peers, and must be taken from a subnet that is different from the
agent’s inband IP subnet.

The syntax for this command is:

set interface ppp <ip_addr> <net-mask>

Example:

set interface ppp enable/enable-always/disable/off/reset

User level: privileged, supervisor.

Use the

set interface ppp

command to enter modem mode, enter terminal

mode, disconnect the PPP session or to reset the connected modem.
The syntax for this command is:

P330-N#

set

interface

inband

1

1.1.1.1

255.255.255.24

Interface inband IP address set.

You must reset the device in order for the change to take

effect.

ip_addr

IP address used by the P330 Supervisor Module to connect via
its PPP interface

net-mask

Subnet mask used by the P330 Supervisor Module to connect
via its PPP interface

P330-N#

set

interface

ppp

149.49.34.125 24

Interface ppp ip address set

«
...
68
69
70
71
72
...
»

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

OfficeConnect 3C855

Brand: 3Com Pages: 4

Brand: PAC Pages: 20

Ubiquity QD2040b

Brand: TCS Pages: 8

Brand: Billion Pages: 35

Brand: Anybus Pages: 2

Brand: Extron electronics Pages: 23

Brand: Sencore Pages: 37

Brand: ZyXEL Communications Pages: 323

Brand: digitalSTROM Pages: 27

Brand: MAXINCOM Pages: 55

Brand: ETC Pages: 5

Brand: ViewSonic Pages: 54

Brand: Fanvil Pages: 6

Brand: Fanvil Pages: 50

Brand: QEI Pages: 47

Brand: Comcast Pages: 8

Brand: Ness Pages: 50

Brand: ZyXEL Communications Pages: 162

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands