Avaya P330 Reference Manual Download Page 298 | Manualshive

Page: 298 / 360

background image

Chapter 4 Load Balancing CLI Commands

280

Avaya

P330 Reference Guide

Real AR Server Commands

To configure a real server to be used by the Application Redirection (AR)
application:
1

Use the

real-ar-server

command to enter a real AR server context.

2

Use any of the remaining

real-ar-server

commands as required.

real-ar-server

User level: user, privileged, supervisor

Use the

real-ar-server

command to create and/or enter a real AR server

context. Use the

no

form of this command to delete a real server from using AR.

The syntax for this command is:

[no] real-ar-server <server-ip>

Example:

real-ar-server admin-status

User level: privileged, supervisor

Use the

admin-status

command to set the administrative status to enable or

disable.

The syntax for this command is:

admin-status <enable | disable>

Example:

server-ip

The IP address of the real server.

Router-N(configure)#

real-ar-server 10.1.1.2

enable

Set admin status to enable.

disable

Set admin status to disable.

Router-N(configure)#

admin-status enable

«
...
296
297
298
299
300
...
»

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

Brand: Banner Pages: 96

Brand: Yeastar Technology Pages: 11

Brand: EchoLife Pages: 16

Brand: New Rock Technologies Pages: 75

Brand: ADTRAN Pages: 8

Brand: RTA Pages: 74

Brand: Motorola Pages: 28

Brand: Motorola Pages: 351

SURFboard eXtreme SBG6782-AC

Brand: Motorola Pages: 2

Brand: Zte Pages: 14

Brand: Internode Pages: 12

Brand: Technicolor Pages: 19

Brand: Fanvil Pages: 5

Brand: ICPDAS Pages: 8

4S Media Server

Brand: Snom Pages: 102

Brand: Celestix Pages: 37

50.0070.0011.00

Brand: FP Pages: 82

Brand: THOMSON Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands