manualshive.com logo in svg

Avaya P330, Reference Manual

The Avaya P330 is a cutting-edge communication device that revolutionizes office connectivity. To unleash its full potential, we provide a comprehensive User Manual, available for free download on our website. Explore the endless capabilities of this innovative product and enhance your communication experience with just a few clicks. {Website} is your go-to destination for acquiring this invaluable manual for the Avaya P330.

Share
Download
background image

Chapter 4        Load Balancing CLI Commands

270

Avaya 

P330 Reference Guide

hc http expected-string

User level: privileged, supervisor

Use the

 expected-string 

command to set the HTTP Health Check expected 

response string. Use the

 

no

 

form of this command to set this to the default value 

(no string).

The syntax for this command is:

[no] expected-string <string>

Example:

hc http expected-string-offset

User level: privileged, supervisor

Use the

 

expected-string-offset

 

command to set the HTTP Health Check 

expected string offset from the end of the Layer 4 Header. Use the

 

no

 

form of this 

command to set this to the default value.

The syntax for this command is:

[no] expected-string-offset <offset>

Example:

string

The string containing the expected response for the Health Check to 
compare the response from the server - a string up to 255 characters.

 Router-N(super-hc-http:7)#

 expected-string <HTML><HEAD>

offset

The offset of the Health Check’s expected string, an integer from 0 - 
1000.

 Router-N(super-hc-http:7)#

 expected-string-offset 5

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

Quark-Elec QK-A032 Setup Manual preview
QK-A032
Brand: Quark-Elec Pages: 2
H3C ICG2000 Installation Manual preview
ICG2000
Brand: H3C Pages: 29
Zero 88 Betapack 4 Manual preview
Betapack 4
Brand: Zero 88 Pages: 16
Elpro Technologies 905U-G User Manual preview
905U-G
Brand: Elpro Technologies Pages: 164
Advantech EDG-4508+ User Manual preview
EDG-4508+
Brand: Advantech Pages: 82
Lindsay Broadband LBDG-250-DC-8200-1 Installation Manual preview
LBDG-250-DC-8200-1
Brand: Lindsay Broadband Pages: 13
Beijer Electronics Korenix JetWave 2310 Series Quick Installation Manual preview
Korenix JetWave 2310 Series
Brand: Beijer Electronics Pages: 2
Arris NVG5 8 Series Quick Start Manual preview
NVG5 8 Series
Brand: Arris Pages: 2
Peavey CAB 16i User Manual preview
CAB 16i
Brand: Peavey Pages: 41
Baxi Gateway 17 Installation Manual preview
Gateway 17
Brand: Baxi Pages: 10
Seneca Z-KEY-P User Manual preview
Z-KEY-P
Brand: Seneca Pages: 52
Seneca Z-KEY User Manual preview
Z-KEY
Brand: Seneca Pages: 99
evertz 78908MG-10GE2 User Manual preview
78908MG-10GE2
Brand: evertz Pages: 52
WELLTECH 3701A Manual preview
3701A
Brand: WELLTECH Pages: 101
Optimus DVA-102ETH Operating Manual preview
DVA-102ETH
Brand: Optimus Pages: 44
2N Telekomunikace 2N StarGate User Manual preview
2N StarGate
Brand: 2N Telekomunikace Pages: 105
4IPNET WHG315 User Manual preview
WHG315
Brand: 4IPNET Pages: 368
RTA 460BMSPBS-N70PB Product User Manual preview
460BMSPBS-N70PB
Brand: RTA Pages: 79

Brands by name

Popular brands

Load more brands