Avaya P330 Reference Manual Download Page 202 | Manualshive

Page: 202 / 360

background image

Chapter 3 Avaya P330 Layer 3 CLI Commands

184

Avaya

P330 Reference Guide

ip max-route-entries

User level: privileged, supervisor.

L

If you are at the ”privileged” level, you can only access this command in
Configure mode.

Type

configure

at the command prompt to enter configure mode.

The

ip max-route-entries

command exists for compatibility with Avaya™

P550. There is no limitation on the size of the routing table, except for the amount of
available memory.
Use the

no

ip max-route-entries

command to remove the limitation.

The syntax for this command is:

[no] ip max-route-entries <value>

Example:

ip netmask-format

User level: privileged, supervisor.

L

If you are at the ”privileged” level, you can only access this command in
Configure mode.

Type

configure

at the command prompt to enter configure mode.

Use the

ip netmask-format

command to specify the format of netmasks in the

show

command output.

Use the

no ip netmask-format

command to restores the default format which is

a dotted decimal.

The syntax for this command is:

[no] ip netmask-format

<mask-format>

The possible mask formats are:

value

Number of entries

Router-N(configure)#

ip

max-route-entries

4000

bitcount

Addresses are followed by a slash and the total number of bits
in the netmask. For example 17

decimal

The network masks are in dotted decimal notation. For
example, 255.255.255.0.

«
...
200
201
202
203
204
...
»

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

Brand: ZyXEL Communications Pages: 2

Brand: Mako Pages: 70

Brand: XLOCK Pages: 2

Brand: Zenitel Pages: 14

Brand: Toshiba Pages: 99

Brand: Hybertone Pages: 33

Brand: Bove Technology Pages: 6

Brand: Paradyne Pages: 31

Brand: Paradyne Pages: 49

Brand: Paradyne Pages: 78

Lightcloud LCGATEWAY

Brand: RAB Pages: 67

Brand: 2Wire Pages: 132

Brand: B+B SmartWorx Pages: 2

Brand: DECODE Pages: 34

AMG1001-T Series

Brand: ZyXEL Communications Pages: 183

TotalStorage NAS Gateway 500

Brand: IBM Pages: 358

Brand: 2N Pages: 35

Brand: SICK Pages: 130

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands