Avaya P330 Reference Manual Download Page 187 | Manualshive

Page: 187 / 360

background image

Chapter 3 Avaya P330 Layer 3 CLI Commands

Avaya

P330 Reference Guide

169

Example: (for Unix):

copy startup-config tftp

User level: privileged, supervisor.

Use the

copy startup-config tftp

command to upload the policy and router

startup configurations to a TFTP server.

The syntax for this command is:

copy startup-config tftp <filename> <ip>

Example:

Example: (for Unix):

copy tftp startup-config

User level: privileged, supervisor.

Copies the policy and router configurations from the saved TFTP file to the Startup
Configuration file in the NVRAM.

The syntax for this command is:

copy tftp startup-config

<filename> <ip>

Router-N(super)#

copy running-config tftp /folder/p330/

startup.cfg 149.49.100.41

filename

Destination file name in the tftp server (full path).

ip

The ip address of the tftp server.

Router-N(super)#

copy startup-config tftp

c:\p330\startup.cfg 149.49.100.41

Router-N(super)#

copy startup-config tftp /folder/p330/

startup.cfg 149.49.100.41

filename

file name (full path)

ip

The ip address of the host

«
...
185
186
187
188
189
...
»

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

Brand: Juniper Pages: 2

Brand: SVS Pages: 4

Brand: Kuhnt Pages: 173

NI WSN C Series

Brand: National Instruments Pages: 16

Brand: Kunbus Pages: 30

GSM Eco Comfort 300-9050V11

Brand: SiKom Pages: 2

Brand: Soyal Pages: 4

Brand: Siemens Pages: 3

Brand: Siemens Pages: 12

6ES7647-0BA00-0YA2

Brand: Siemens Pages: 71

Brand: Siemens Pages: 138

Advance Network Gateway

Brand: Siemens Pages: 72

Brand: Siemens Pages: 94

Brand: UfiSpace Pages: 27

Brand: Next Level Security Systems Pages: 10

Brand: Nortel Pages: 134

Remote Office 9150

Brand: Nortel Pages: 570

Brand: TCAM Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands