manualshive.com logo in svg

Avaya P330, Reference Manual

The Avaya P330 is a cutting-edge communication device that revolutionizes office connectivity. To unleash its full potential, we provide a comprehensive User Manual, available for free download on our website. Explore the endless capabilities of this innovative product and enhance your communication experience with just a few clicks. {Website} is your go-to destination for acquiring this invaluable manual for the Avaya P330.

Share
Download
background image

Chapter 3        Avaya P330 Layer 3 CLI Commands

Avaya 

P330 Reference Guide

199

Example: 

set qos dscp-name

User level: privileged, supervisor.

L

This command applies to the P333R only.

L

If you are at the ”privileged” level, you can only access this command in 
Configure mode.

 

Type 

configure

 at the command prompt to enter Configure mode if 

necessary.

Use the 

set qos dscp-name

 command to configure the DSCP entry name. 

The syntax for this command is:

set qos dscp-name <dscp> <name>

Example:

L

If you wish to enter a name which includes spaces, you must enclose the entire 
name in quotation marks, for example “new york”.

set qos policy-source

User level: privileged, supervisor.

L

If you are at the ”privileged” level, you can only access this command in 
Configure mode.

 

Type 

configure

 at the command prompt to enter Configure mode if 

necessary.

Router-N(configure)# 

set

 

qos

 

dcsp-cos-map

 

9-16

 

fwd3

dscp1

dscp entry (0-63)

name

entry name

Router-N(configure)# 

set

 

qos

 

dscp-name

 

10

 

special

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

TempAlert TM-WIFI440-Z User Manual preview
TM-WIFI440-Z
Brand: TempAlert Pages: 22
B&B Electronics GW-7472 User Manual preview
GW-7472
Brand: B&B Electronics Pages: 60
Vega BS Series User Manual preview
BS Series
Brand: Vega Pages: 39
Xiaomi Mi Smart Home Kit Manual preview
Mi Smart Home Kit
Brand: Xiaomi Pages: 4
Crestron Electronics AirMedia AM-3100-WF(-I) Reference Manual preview
AirMedia AM-3100-WF(-I)
Brand: Crestron Electronics Pages: 91
Comtech EF Data NetPerformer SDM-9 Series Hardware Installation Manual preview
NetPerformer SDM-9 Series
Brand: Comtech EF Data Pages: 136
Sollae SIG-5441 User Manual preview
SIG-5441
Brand: Sollae Pages: 38
Enttec DMX ETHERGATE MK3 Quick Start Manual preview
DMX ETHERGATE MK3
Brand: Enttec Pages: 6
Matrix SETU VFXTH System Manual preview
SETU VFXTH
Brand: Matrix Pages: 322
Gree ME30-44/D2 B Owner'S Manual preview
ME30-44/D2 B
Brand: Gree Pages: 24
Netphonic NG-48 Series User Manual preview
NG-48 Series
Brand: Netphonic Pages: 36
Netopia Cayman 3500 Series Quick Start Manual preview
Cayman 3500 Series
Brand: Netopia Pages: 2
Netopia 3347W Specifications preview
3347W
Brand: Netopia Pages: 2
Netscape NETSCAPE DIRECTORY SERVER 7.0 Reference preview
NETSCAPE DIRECTORY SERVER 7.0
Brand: Netscape Pages: 178
Imagine communications Selenio VMG-14+ Hardware Setup Manual preview
Selenio VMG-14+
Brand: Imagine communications Pages: 92
Comelit 1456 Technical Manual preview
1456
Brand: Comelit Pages: 28
Kaon CG2200 Quick Installation Manual preview
CG2200
Brand: Kaon Pages: 12
TRI02SYS EnOcean 02LINE Installation And Operating Manual preview
EnOcean 02LINE
Brand: TRI02SYS Pages: 4

Brands by name

Popular brands

Load more brands