Avaya P330 Reference Manual Download Page 340 | Manualshive

Page: 340 / 360

background image

Chapter 4 Load Balancing CLI Commands

322

Avaya

P330 Reference Guide

virtual-server

User level: privileged, supervisor

Use the

virtual-server

command to create/enter a virtual server context. Use

the

no

form of this command to delete a virtual server.

The syntax for this command is:

[no] virtual-server <server name>

Example:

virtual-server admin-status

User level: privileged, supervisor

Use the

admin-status

command to set the administrative status to enable or

disable.

The syntax for this command is:

admin-status <enable | disable>

Example:

virtual-server id

User level: privileged, supervisor

Use the

id

command to set the identification number for the virtual server.

The syntax for this command is:

id <server-id>

server name

The name of the virtual server, a string of up to 80
characters.

Router-N(configure)#

virtual-server srvr1

enable

Set admin status to enable.

disable

Set admin status to disable.

Router-N(configure)#

admin-status enable

server-id

Identification number for the virtual server, an integer from 1 to
1024.

«
...
338
339
340
341
342
...
»

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

Brand: Kuhnt Pages: 173

Brand: Gateway Pages: 2

Brand: QUPIT Pages: 16

Brand: QUNDIS Pages: 48

Brand: Nitgen Pages: 36

SMK Access Station Mini

Brand: Sigfox Pages: 17

Brand: Innovaphone Pages: 24

Dynalite DTK622-USB

Brand: Philips Pages: 2

Dynalite DMNG232

Brand: Philips Pages: 2

Dynalite DDNI-LON

Brand: Philips Pages: 2

Dynalite DDNG485

Brand: Philips Pages: 2

Dynalite DDNG232

Brand: Philips Pages: 2

Dynalite DDNG100BT

Brand: Philips Pages: 2

Dynalite DDNG-KNX

Brand: Philips Pages: 2

Dynalite DDMIDC8

Brand: Philips Pages: 2

Brand: Philips Pages: 80

Brand: Toshiba Pages: 99

Brand: Popp Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands