manualshive.com logo in svg

Avaya P330, Reference Manual

The Avaya P330 is a cutting-edge communication device that revolutionizes office connectivity. To unleash its full potential, we provide a comprehensive User Manual, available for free download on our website. Explore the endless capabilities of this innovative product and enhance your communication experience with just a few clicks. {Website} is your go-to destination for acquiring this invaluable manual for the Avaya P330.

Share
Download
background image

Chapter 3        Avaya P330 Layer 3 CLI Commands

Avaya 

P330 Reference Guide

195

The default is 

disabled

.

The syntax for this command is:

[no] router ospf

Example:

router rip

User level: privileged, supervisor.

L

If you are at the ”privileged” level, you can only access this command in 
Configure mode.

 

Type 

configure

 at the command prompt to enter interface mode.

Use the 

router rip

 command to configure the Routing Information Protocol 

(RIP) and enter the “router rip” context. 
Use the 

no router rip 

 command to disable RIP. 

The default state is disabled.

The syntax for this command is:

[no] router rip

Example:
To enable the RIP protocol: 

router srrp

User level: privileged, supervisor.

L

If you are at the ”privileged” level, you can only access this command in 
Configure mode.

 

Type 

configure

 at the command prompt to enter configure mode if necessary.

Use the 

router srrp

 command to enable srrp redundancy for the main router 

and enter the “router srrp” context.
Use the 

no router srrp

 command to disble srrp redundancy for the main router.

Router-N(configure)# 

router

 

ospf

Done!

Router-N(configure router:ospf)# 

Router-N(configure)# 

router

 

rip

Done!

Router-N(configure router:rip)# 

Summary of Contents for P330









































































































































































































































































































































































Reviews:

No comments

Related manuals for P330

QEI ePAQ-942 Series User Manual preview
ePAQ-942 Series
Brand: QEI Pages: 42
Abocom HA2500 Specification Sheet preview
HA2500
Brand: Abocom Pages: 2
3Com OFFICE CONNECT CABLE/DSL SECURE GATEWAY... User Manual preview
OFFICE CONNECT CABLE/DSL SECURE GATEWAY...
Brand: 3Com Pages: 102
ABB TG/S 3.1 Product Manual preview
TG/S 3.1
Brand: ABB Pages: 45
ABB RER601 Technical Manual preview
RER601
Brand: ABB Pages: 108
NETGEAR C3700 Installation Manual preview
C3700
Brand: NETGEAR Pages: 2
NETGEAR C3000 User Manual preview
C3000
Brand: NETGEAR Pages: 76
Netgate SG-1100 Manual preview
SG-1100
Brand: Netgate Pages: 58
Neteyes NexusWay 800 Series User Manual preview
NexusWay 800 Series
Brand: Neteyes Pages: 118
HD HD29564 Quick Start Manual preview
HD29564
Brand: HD Pages: 2
Elko SmartHUB EKO07235 Manual preview
SmartHUB EKO07235
Brand: Elko Pages: 4
Elko iNELS AirGTW-FWD Quick Start Manual preview
iNELS AirGTW-FWD
Brand: Elko Pages: 12
ETC Response SMPTE Setup Manual preview
Response SMPTE
Brand: ETC Pages: 5
Fanvil G100S User Manual preview
G100S
Brand: Fanvil Pages: 41
Fanvil GA10 User Manual preview
GA10
Brand: Fanvil Pages: 54
Encom Harmony IP I/O8 User Manual preview
Harmony IP I/O8
Brand: Encom Pages: 44
Technicolor MediaAccess TG799vn Setup And User Manual preview
MediaAccess TG799vn
Brand: Technicolor Pages: 128
Kinnex Media Gateway Quick Start Manual preview
Media Gateway
Brand: Kinnex Pages: 26

Brands by name

Popular brands

Load more brands