Tema Telecomunicazioni DIAL-112 Technical Installation Manual Download Page 1

Page: 1 / 35

Revision Date

Revision reason

Prepared

Checked/Approved

14/07/2010 Update

GBC,MM

MAS-DIAL112-REV06EN

Page 1 of 35

DIAL-112

GSM Gateway Voice Interface

for ISDN BRI

TECHNICAL – INSTALLATION MANUAL

PRELIMINARY DOCUMENTATION

Version HW 1.0 - Version SW 1.11

Made in Italy by TEMA TELECOMUNICAZIONI S.r.l.

Recommendations

Use only original spare parts and consumables supplied by Tema Telecomunicazioni Srl for this equipment. The company shall

not be held responsible for any damage caused by the use of materials that they have not supplied.

The device has been carefully manufactured and tested. In any case, the product is not recommended for use in situations in

which incorrect operating may result in damage to persons and/or property.

We recommend that you carefully read all this manual before starting to use the device.

Do not expose the device to sunlight and protect it from sources of heat, dust, humidity and chemical agents.

This manual is the property of Tema Telecomunicazioni Srl and any duplication and reproduction, even partial, as well as

storage on any type of media is forbidden without written permission from Tema Telecomunicazioni Srl.

TEMA TELECOMUNICAZIONI S.r.l.

Telecommunications - Electronics

Summary of Contents for DIAL-112




































Search results

Summary of Contents for DIAL-112

Reviews:

Related manuals for DIAL-112

Brands by name

Popular brands

Tema Telecomunicazioni DIAL-112, Technical Installation Manual

Search results

Summary of Contents for DIAL-112

Reviews:

Related manuals for DIAL-112

Brands by name

Popular brands