Asentria SiteBoss 571 UserManual
Page 6
SiteBoss 571 2.10.150 STD Serial # : 571010405
Site Name : 571-571010405
Date : MON 01/20/14 1: 19200,8N1 I/O 1
Time : 08:59:17 2: 19200,8N1 I/O 2
Modem : None 3: 19200,8N1 I/O 3
Eth 1 : STATIC 4: 19200,8N1 I/O 4
IP Add : 10.10.5.124 5: 19200,8N1 I/O 5
MAC Add : 00:10:A3:80:F1:29 6: 19200,8N1 I/O 6
IPv6 : OFF 7: 19200,8N1 I/O 7
Eth 2 : STATIC 8: 19200,8N1 I/O 8
IP Add : 0.0.0.0 9: 19200,8N1 I/O 9
MAC Add : 00:10:A3:80:F1:2A 10: 19200,8N1 I/O 10
IPv6 : OFF 11: 19200,8N1 I/O 11
Outputs : AAAAA AAAA 12: 19200,8N1 I/O 12
Temp : 89 F 13: 19200,8N1 I/O 13
14: 19200,8N1 I/O 14
15: 19200,8N1 I/O 15
16: 19200,8N1 I/O 16
When the Status screen appears, the unit is successfully connected and ready for use.
Via the Asentri
a
OmniDiscover program
1. From the Asentria website (
http://www.asentria.com/docsandsoftware/productManuals.aspx
), or the
Documentation and Utilities CD, download the OmniDiscover program. This program will allow you to locate
devices on your network (i.e.: the S571) with Asentria MAC addresses, and allow you to assign the network
settings directly over the network, thus eliminating the need for the serial port connection as described above.
2. Open the OmniDiscover program. It will immediately display all Asentria devices on the network. Right
clicking on the line for this unit displays three options: Setup, Telnet and Web.
Setup
opens another window where the IP Address, Subnet Mask, and Gateway (router) can be
configured (see bel
ow). Press “OK” and these will be assigned to the unit and displayed in the previous
window. (Select this option to configure the network settings for the first time.)
Telnet
opens a connection to the device using your default Telnet client.
Web
opens an HTTP connection to the device using your default browser, if the device supports and is
configured to allow a web connection.
3. Once the network settings have been assigned, the S571 command line can be accessed via any Telnet client
or HTTP web connection.
Contact
for any questions or assistance with OmniDiscover.
Network Setup
Via OmniDiscover connection:
1. See the description of how to use
Via serial connection:
1. From the command prompt access the Main Setup Menu by typing
SETUP
and pressing <Enter>.
2. Select the Network Settings branch.
3. Select A) Ethernet Settings and select the Ethernet interface that corresponds to the one on the back panel
that you plugged your network cable into.
4. Enter an IP address, subnet mask and--if necessary--a router address.
5. Toggle NAT on/off as desired.
6. If using this Ethernet interface for a VLAN connection, select this option to configure any of six VLAN
connections. See the
section in the Features chapter for details on how to configure.
7. Press <ESC> to go back one level in the menu tree, or <CTRL + C> to exit the Main Setup Menu and return to
the command prompt.
