APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download | Manualshive

Page: 70 / 408

background image

•

Check the gap between the electrodes with a feeler gauge.

CAUTION

DO NOT ATTEMPT TO READJUST THE ELECTRODE GAP.

The gap between the electrodes should be 0.6 -

0.7 mm (0.023 - 0.027 in) Wear limit is achieved

when the gap for one of the two electrodes rea-

ches 1.0 mm (0.039 in)

•

Make sure the washer is in good con-

ditions.

Installation:

•

Once the washer is fitted, screw the

spark plug carefully to avoid damaging

the thread.

•

Screw the spark plug to the prescribed

torque.

CAUTION

TIGHTEN THE SPARK PLUG CORRECTLY, OTHERWISE
THE ENGINE MAY OVERHEAT AND GET IRRETRIEVABLE
DAMAGED. USE ONLY THE RECOMMENDED TYPE OF
SPARK PLUG, OTHERWISE, THE ENGINE DURATION AND
PERFORMANCE COULD BE COMPROMISED.

See also

Engine

Engine oil

Check

Check the engine oil level frequently.

NOTE

CARRY OUT MAINTENANCE OPERATIONS AT HALF THE INTERVALS SPECIFIED IF THE VE-
HICLE IS USED IN PARTICULAR RAINY OR DUSTY CONDITIONS, OFF ROAD OR FOR TRACK
USE.

ENGINE OIL LEVEL MUST BE CHECKED WHEN THE ENGINE IS WARM.
IF YOU CHECK LEVEL WHEN THE ENGINE IS COLD, OIL LEVEL COULD TEMPORARILY DROP
BELOW THE "MIN" MARK.
THIS SHOULD NOT BE CONSIDERED A PROBLEM PROVIDED THAT THE ALARM WARNING
LIGHT AND THE ENGINE OIL PRESSURE ICON ON THE DISPLAY DO NOT TURN ON SIMULTA-
NEOUSLY.

CAUTION

Maintenance

DORSODURO 1200 ABS - ATC

MAIN - 70

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
68
69
70
71
72
...
»

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO 1200 ABS - ATC

Brand: GAS GAS Pages: 70

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

ST400 Cruiser Edition

Brand: STEEL HORSE AUDIO Pages: 6

Brand: GAS GAS Pages: 119

Brand: Suzuki Pages: 89

V 7 CAFE CLASSIC

Brand: MOTO GUZZI Pages: 147

Brand: Clas Ohlson Pages: 5

690 Enduro AUS 2010

Brand: KTM Pages: 265

SCARABEO 100 4T - 06-2001 PART6

Brand: APRILIA Pages: 6

Brand: Yamaha Pages: 398

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands