APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download

Page: 169 / 408

•

short circuit to positive / short circuit to negative / open circuit, overvoltage, excessive internal

temperature.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 29 - 41. If shorted to

negative: no voltage has been detected. If the circuit is open: an interruption or excessive

ampere input or control unit overheating has been detected

Troubleshooting

•

If shorted to positive: disconnect the throttle body connector, set key to ON and check volt-

age at PIN 3: if the voltage read is higher or equal to 5V, there is a short circuit on the cable

harness; replace the throttle body if the voltage is null

•

If shorted to negative: disconnect the throttle body connector, set the key to ON and check

if PIN 3 is in continuity with the vehicle ground connection: if there is continuity, restore the

cable harness; if there is not continuity, replace the throttle body

•

If the circuit is open, there is overvoltage or excessive internal temperature: check the throttle

body connector and the control unit connector: if not OK, restore; if OK, disconnect the

throttle body connector and control unit connector and check if there is cables continuity; if

there is no continuity, restore the cable harness. If there is continuity, with the throttle body

connector connected, check that the resistance, from the throttle control unit connector,

between PIN 29 and 41 is within 1 and 2.5 Ohm; if it is not, replace the throttle body; if it is,

check that the throttle body is not mechanically blocked: if blocked, solve the problem and

replace the body; if it is not, replace the control unit

Rear throttle control circuit P0186

•

short circuit to positive / short circuit to negative / open circuit, overvoltage, excessive internal

temperature circuit open

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 3 - 15. If shorted to neg-

ative: no voltage has been detected. If the circuit is open: an interruption or excessive

ampere input or control unit overheating has been detected

Troubleshooting

•

If shorted to positive: disconnect the throttle body connector, set key to ON and check volt-

age at PIN 3: if the voltage read is higher or equal to 5V, there is a short circuit on the cable

harness; replace the throttle body if the voltage is null

•

If shorted to negative: disconnect the throttle body connector, set the key to ON and check

if PIN 3 is in continuity with the vehicle ground connection: if there is continuity, restore the

cable harness; if there is not continuity, replace the throttle body

•

If the circuit is open, there is overvoltage or excessive internal temperature: check the throttle

body connector and the control unit connector: if not OK, restore; if OK, disconnect the

DORSODURO 1200 ABS - ATC

Electrical system

ELE SYS - 169

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands

APRILIA DORSODURO 1200 ABS - ATC, Service Station Manual

Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands