manualshive.com logo in svg

APRILIA DORSODURO 1200 ABS - ATC, Service Station Manual

Share
Download
APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download Page 322

•

Fit the entire fork upper plate, adjusting

with short taps with a rubber hammer

•

Fit the washer and tighten the upper

plug to the specified tightening torque.

STEERING UPPER PLATE

pos.

Description

Type

Quantity

Torque

Notes

2

Headstock cap

M22x1

1

100 Nm (73.75 lbf ft)

-

3

TCEI screw fastening fork legs to

bottom yoke

M8x35

4

25 Nm (18.44 lbf ft)

-

4

TCEI screw fastening U-bolt onto

fork yoke

M10x60

2

50 Nm (36.88 lbf ft)

-

5

TCEI screw fastening fork legs to top

yoke

M8x30

2

25 Nm (18.44 lbf ft)

-

6

Headstock counter-lock ring

M25x1

1

-

Tighten by hand

•

Tighten the fixing screws of the upper

plate to the prescribed tightening tor-

que.

When refitting the U-bolt, position the two referen-

ces facing the front part of the vehicle.

Suspensions

DORSODURO 1200 ABS - ATC

SUSP - 322

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands