APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download

Page: 168 / 408

there is power (+5 V) at the throttle body connector PIN 2, and that PIN 6 is connected to

ground. If both are correct, replace the throttle body

potentiometer 1 sensor, rear throttle position P0125

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 36. If the circuit is open,

shorted to negative: voltage equal to zero has been detected at PIN 36

Troubleshooting

•

If shorted to positive: check the value shown by the parameter of the Rear throttle Potenti-

ometer 1 (voltage): disconnect the connector and read the value indicated by the diagnosis

instrument: if the voltage does not vary, there is a short circuit in the cable wiring; replace

the throttle body if the voltage drops to zero.

•

If the circuit is open, shorted to negative: check the throttle body connector and the control

unit connector. If not OK, restore; if everything is OK, check circuit continuity between the

two terminals. If not OK, restore the cable harness; if OK, check the circuit ground insulation

(from throttle sensor connector or control unit connector). If it is ground insulated, check that

there is power (+5 V) at the throttle body connector PIN 2, and that PIN 6 is connected to

ground. If both are correct, replace the throttle body

potentiometer 2 sensor, rear throttle position P0127

•

short circuit to positive / open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 21. If the circuit is open,

shorted to negative: voltage equal to zero has been detected at PIN 21.

Troubleshooting

•

If shorted to positive: check the value shown by the parameter of the Rear throttle Potenti-

ometer 2 (voltage): disconnect the connector and read the value indicated by the diagnosis

instrument: if the voltage does not vary, there is a short circuit in the cable wiring; replace

the throttle body if the voltage drops to zero.

•

If the circuit is open, shorted to negative: check the throttle body connector and the control

unit connector. If not OK, restore; if everything is OK, check circuit continuity between the

two terminals. If not OK, restore the cable harness; if OK, check the circuit ground insulation

(from throttle sensor connector or control unit connector). If it is ground insulated, check that

there is power (+5 V) at the throttle body connector PIN 2, and that PIN 6 is connected to

ground. If both are correct, replace the throttle body

Front throttle control circuit P0166

Electrical system

DORSODURO 1200 ABS - ATC

ELE SYS - 168

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands

APRILIA DORSODURO 1200 ABS - ATC, Service Station Manual

Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands