APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download

Page: 315 / 408

•

Fit the sleeve on the stem and set the

oil seal into position with the aid of the

specific tool.

Specific tooling

AP8140189

Oil seal fitting tool for Ø 43 mm

(1.69 in) orifices

AP8140146

Weight

•

Insert the retainer ring in its position.

•

Fit the dust gaiter with the specific tool.

Specific tooling

AP8140189

Oil seal fitting tool for Ø 43 mm

(1.69 in) orifices

AP8140146

Weight

DORSODURO 1200 ABS - ATC

Suspensions

SUSP - 315

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands

APRILIA DORSODURO 1200 ABS - ATC, Service Station Manual

Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands