APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download

Page: 308 / 408

Disassembling the fork

NOTE

THE OPERATIONS DESCRIBED BELOW ARE VALID FOR BOTH STEMS.

•

Using the appropriate tool fasten the

fork in the vice.

Specific tooling

AP8140149

Protection for fitting operations

•

Operating on the upper screw, unload

the spring.

•

Loosen the cover without unscrewing it

completely.

Suspensions

DORSODURO 1200 ABS - ATC

SUSP - 308

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands

APRILIA DORSODURO 1200 ABS - ATC, Service Station Manual

Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands