APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download | Manualshive

Page: 310 / 408

background image

•

Remove the lock nut and the washer.

•

Remove the spring paying attention to

drain the oil correctly.

•

Drain the oil into a container of suitable

capacity to collect fluids.

DO NOT DISPOSE OF OIL INTO THE ENVIRONMENT.
DISPOSE OF ENGINE OIL IN A SEALED CONTAINER AND
TAKE IT TO YOUR SUPPLIER OR TO THE NEAREST USED
OIL COLLECTION CENTRE.

•

Discharge the fork, remove the internal

dipstick of the pumping member pin (1)

and the washer (2).

•

Operate repeatedly on the pumping

member pin (3) so as to drain com-

pletely the oil from inside.

Suspensions

DORSODURO 1200 ABS - ATC

SUSP - 310

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
308
309
310
311
312
...
»

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO 1200 ABS - ATC

Brand: LAZER Pages: 19

Brand: MRA Pages: 9

Brand: Parweld Pages: 4

Brand: hepco & becker Pages: 4

Brand: Artotic Pages: 9

Brand: Suzuki Pages: 165

Brand: Ops-Core Pages: 20

HelmetTalk HTCS-3O

Brand: Nady Systems Pages: 2

Brand: O'Neal Pages: 12

Brand: Malaguti Pages: 292

Brand: Benelli Pages: 15

Brand: Benelli Pages: 314

Brand: KTM Pages: 12

Brand: Polaris Pages: 308

Brand: Race Dynamics Pages: 28

Brand: Baja Pages: 8

Brand: Honda Pages: 184

Brand: Ohlins Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands