APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download | Manualshive

Page: 145 / 408

background image

•

Example value with key ON: 1004 mbar

•

Example value with engine on: 735 mbar

•

NOTE: pressure estimated by the control unit according to the throttle position

Rear Cylinder estimated Intake Pressure

•

Example value with key ON: 1003 mbar

•

Example value with engine on: 721 mbar

•

NOTE: pressure estimated by the control unit according to the throttle position

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

DIAGNOSIS INSTRUMENT: ELECTRICAL ERRORS

front cylinder air pressure sensor P0105

•

shorted to positive / open circuit, shorted to negative.

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 24. If the circuit is open,

shorted to negative: voltage equal to zero has been detected at PIN 24.

Troubleshooting

•

If shorted to positive: verify that the parameter of the front cylinder air Pressure Sensor on

the diagnosis instrument is approx. 1200 mbar; disconnect the sensor connector: if the value

does not vary, it means that the cable is shorted between the control unit connector and the

sensor connector: restore the cable harness; Replace the sensor if the value varies.

•

If the circuit is open, shorted to negative: check the Marelli control unit connector and the

sensor connector; if not OK, restore. If everything is OK, with key set to OFF, check if there

is continuity between the PIN 24 of the Marelli control unit and the sensor connector PIN 3:

if there is no continuity, restore the cable harness. If there is continuity, check the cable

ground insulation: if there is continuity to ground, restore the cable harness; if not, with key

set to ON check that the voltage on sensor connector PIN 1 is approx. 5 V: if not OK, set

the key to OFF and check continuity between the ENGINE connector PIN 25 and the sensor

connector PIN 1: if not OK, restore the cable harness; if OK, replace the control unit; if there

is 5V voltage at PIN 1, and with key set to ON, check the continuity to ground of the sensor

connector PIN 3: if not OK, restore the cable harness; if OK, replace the sensor.

rear cylinder air pressure sensor P0106

•

shorted to positive / open circuit, shorted to negative.

Error cause

DORSODURO 1200 ABS - ATC

Electrical system

ELE SYS - 145

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
143
144
145
146
147
...
»

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO 1200 ABS - ATC

Brand: Kappa Pages: 4

Brand: Baja motorsports Pages: 8

Brand: Yukon Trail Pages: 24

Brand: R&G Pages: 22

Brand: R&G Pages: 8

Brand: TB Pages: 8

Brand: GAS GAS Pages: 150

2001 GSX1300RK1 HAYABUSA

Brand: Suzuki Pages: 31

Brand: oset Pages: 44

Brand: X-lite Pages: 96

Brand: Yamaha Pages: 81

2011 Star XV250A

Brand: Yamaha Pages: 90

2011 V Star XVS650A

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 96

2010 V Star XVS650AZ

Brand: Yamaha Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands