APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download

Page: 237 / 408

•

Tighten the nut and proceed to caulk.

CAUTION

BE CAREFUL WITH THE CUPPED RING FITTING SIDE;
THE RING CONE SHALL BE DIRECTED TOWARDS THE
ENGINE.

•

Insert the cupped ring (1).

CAUTION

BE CAREFUL WITH THE CUPPED RING FITTING SIDE;
THE RING CONE SHALL BE DIRECTED TOWARDS THE
ENGINE.

•

Fit the lathed driven disc (2).

•

Fit the nitrided steel disc (3).

•

Fit the clutch plates. Start with the fric-

tion material discs and alternate with

steel discs.

•

Position all friction material discs with

their teeth aligned in one of the long

slots of the clutch housing.

•

Place the control rod.

•

Place the thrust plate.

CAUTION

ENSURE TO ALIGN THE ARROW ON THRUST PLATE
WITH THE MACHINED REFERENCE ON HUB.

DORSODURO 1200 ABS - ATC

Engine

ENG - 237

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands

APRILIA DORSODURO 1200 ABS - ATC, Service Station Manual

Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands