APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download

Page: 267 / 408

•

Check for cracks on the piston and for compression on the piston sliding surface (seizing);

Replace the piston if required.

CAUTION

SMALL STRIATIONS ON THE PISTON LINER ARE ADMISSIBLE.

•

Measure the pin outside diameter (a)

and if not complying with specifica-

tions, replace the pin.

Pin outside diameter: 22.00 - 21.97 mm (0.8661

- 0.8650 in) Limit: 21.96 mm (0.8646 in)

•

Measure the pin housing diameter (b)

and replace the piston if not complying

with specifications.

Pin housing diameter (b): 22.010 - 22.015 mm

(0.8665 - 0.8667 in)

•

Calculate the clearance between pin

and pin hole and, if not complying with

specifications, replace both pin and

piston.

Pin - piston clearance: C = b - a

0.010 - 0.045 mm (0.0004 - 0.0018 in)

Limit: 0.060 mm (0.0024 in)

YLINDER

PISTON

COUPLING

Name

Initials

Cylinder

Piston

Play on fitting

Cylinder-piston clear-

ance A - A

Type A - A

105.990 - 105.997 mm

(4.1728 - 4.1731 in)

105.928 - 105.935 mm

(4.1704 - 4.1707 in)

0.055 - 0.069 mm

(0.0022 - 0.0027 in)

Cylinder-piston clear-

ance B - B

Type B - B

105.997 - 106.004 mm

(4.1731 - 4.1734 in)

105.935 - 105.942 mm

(4.1707 - 4.1709 in)

0.055 - 0.069 mm

(0.0022 - 0.0027 in)

Cylinder-piston clear-

ance C - C

Type C -C

106.004 - 106.011 mm

(4.1734 - 4.1736 in)

105.942 - 105.949 mm

(4.1709 - 4.1712 in)

0.055 - 0.069 mm

(0.0022 - 0.0027 in)

Cylinder-piston clear-

ance D - D

Type D - D

106.011 - 106.018 mm

(4.1736 - 4.1739 in)

105.949 - 105.956 mm

(4.1712 - 4.1715 in)

0.055 - 0.069 mm

(0.0022 - 0.0027 in)

NOTE

MAXIMUM CLEARANCE AT WEAR LIMIT 0.085 mm (0.0033 in)

Installing the cylinder

•

Fit the stud bolts, if previously removed.

CAUTION

THE STUD BOLTS SHOULD BE FITTED SO THAT THEY PROTRUDE.

DORSODURO 1200 ABS - ATC

Engine

ENG - 267

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands

APRILIA DORSODURO 1200 ABS - ATC, Service Station Manual

Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands