APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download

Page: 361 / 408

•

In this case, the bleed process must be accompanied by further pedal strokes and with the

bleed device connected (about 5 for each wheel circuit).

BLEED SYSTEM AFTER BRAKE PUMP RE-

PLACEMENT

PRELIMINARY OPERATIONS

•

Install the new brake pump.

•

Connect the reservoir to the brake

pump.

•

Connect the brake pipe to the pump

line coupling.

•

Fill the reservoir with new DOT4 brake

fluid.

REGULAR BLEEDING SYSTEM

•

Connect the bleed bottle to the bleed screw of the front brake calliper.

•

Operate the brake lever.

•

Open the bleed screw until all the pressure has been release and then close it.

•

Release the brake lever.

•

After releasing the lever, wait two seconds so that the brake fluid flows into the cylinder.

•

Repeat this procedure until the brake fluid is clear and has no air bubbles. (about 10 to 20

times).

NOTE: CHECK BRAKE FLUID LEVEL IN THE RESERVOIR AND, IF NECESSARY, TOP UP

(CHECKING BRAKE PAD WEAR).

•

Then perform the same procedure for the rear brake calliper, acting only on the valve in-

stalled on that calliper.

•

Fill the reservoir until it reaches the reference "MAX" and refit the cap (check pad wear).

•

Detach the bleed hoses and close the bleed screws again to the correct tightening torque.

•

Check the stroke and the sensitivity of both the lever and the brake pedal.

NOTE: IF AFTER BLEEDING, THE STROKE OF THE PEDAL OR THE LEVER IS TOO LONG,

CHECK THAT THERE ARE NO LEAKS IN THE BRAKING SYSTEM AND IF EVERYTHING IS OK,

CONTINUE BLEEDING OPERATIONS USING NAVIGATOR.

DORSODURO 1200 ABS - ATC

Braking system

BRAK SYS - 361

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands

APRILIA DORSODURO 1200 ABS - ATC, Service Station Manual

Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands