APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download | Manualshive

Page: 177 / 408

background image

PIN 64: gear indication: closed circuit (continuity);

gear engaged: open circuit (infinite resistance).

Gear engaged circuit resistance: 1st gear: 0.8

kohm, 2nd gear 0.5 kohm, 3rd gear 15.0 kohm, 4th

gear 6.9 kohm, 5th gear 2.8 kohm, 6th gear 1.5

kohm.

Pin out:

White/Black: ground from ECU, Light Blue: + 12V

from ECU (gear), Pink: + 5V from ECU (gears).

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING,
CAREFULLY READ THE GENERAL TROUBLESHOOTING
CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGIN-
NING OF THE CHECK AND CONTROL SECTION IN THE
ELECTRICAL SYSTEM CHAPTER.

DIAGNOSIS INSTRUMENT: STATUSES

Gear in neutral

•

Yes/No

Gear engaged: 0 - 1 - 2- 3 - 4 - 5 - 6

DIAGNOSIS INSTRUMENT: ELECTRICAL ERRORS

Gear sensor P0461

•

shorted to positive or open circuit / shorted to negative.

Error cause

•

If the circuit is open, shorted to positive: excessive voltage has been detected at PIN 72. If

shorted to negative: voltage equal to zero has been detected at PIN 72.

Troubleshooting

•

If the circuit is open, shorted to positive: the error is detected with gear engaged only. Check

the sensor connector and the VEHICLE connector of the control unit: if not OK, restore; if

they are OK, check the continuity of the grey/black cable between the two connectors: if not

OK, restore; if they are OK, with key set to ON and control unit connector disconnected,

check from the control unit side if the cable is in voltage: if it is in voltage, disconnect the

sensor connector and check if the cable is in voltage: if it is in voltage, restore the cable

harness; if it is not in voltage, replace the sensor (there is an interruption or shorted to positive

of the pink cable in the section from the sensor connector to the sensor or inside the sensor).

•

If shorted to negative: disconnect the sensor connector and with key set to ON, check grey/

black cable voltage: if equal to zero, restore the cable harness; if equal to approx. 5 V,

replace the sensor (there is short circuit to ground of the pink cable in the section from the

sensor connector to the sensor or inside the sensor).

DORSODURO 1200 ABS - ATC

Electrical system

ELE SYS - 177

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
175
176
177
178
179
...
»

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO 1200 ABS - ATC

Brand: Can-Am Pages: 16

Brand: Can-Am Pages: 254

Brand: Öhlins Pages: 8

651665 00 22-00-40

Brand: hepco & becker Pages: 5

Brand: LAZER Pages: 19

Brand: Kong Pages: 72

Brand: AGV Pages: 45

Brand: Sena Pages: 25

Fastway PMB-01-5203

Brand: Pro Moto Billet Pages: 2

RMAX WOLVERINE 2021

Brand: Yamaha Pages: 192

Brand: Yamaha Pages: 396

Brand: Yamaha Pages: 192

Brand: Yamaha Pages: 166

Brand: Yamaha Pages: 166

Brand: Yamaha Pages: 198

Brand: Yamaha Pages: 274

Brand: Yamaha Pages: 356

Brand: Yamaha Pages: 376

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands