APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download

Page: 154 / 408

CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGIN-
NING OF THE CHECK AND CONTROL SECTION IN THE
ELECTRICAL SYSTEM CHAPTER.

DIAGNOSIS INSTRUMENT: STATUSES

Lambda probe: Start-up_Lean_Rich_Fault due to rich value_Fault due to lean value

•

If the probe connector is removed (voltage almost equal to zero), the status is Fault due to

lean value

Lambda check: Open loop/Closed loop/Rich in closed loop/Lean in closed loop/enriched

•

Closed loop indicates that the control unit is using the lambda probe signal to keep the

combustion as close as possible to the stoichiometric value.

DIAGNOSIS INSTRUMENT: ACTIVATION

Lambda probe heating

•

The auxiliary injection relay (No. 35 in the wiring diagram, placed in the front relay box, left

side; CHECK, however, the identification of the relay with the colour of the cables) is ener-

gised and the heating circuit is closed to ground 5 times (pin 3 of the lambda probe

connector). The continuity of the wiring is necessary for correct activation: no error indica-

tions are displayed in case of lack of activation

DIAGNOSIS INSTRUMENT: ELECTRICAL ERRORS

lambda probe P0130

•

shorted to positive

Error cause

•

Excessive voltage (battery voltage) has been detected at PIN 10 and 22 of the ENGINE

connector. Caution: the 'lambda probe' parameter is not the real value that is read; a re-

covery value is displayed instead. The instrument panel does not indicate the presence of

this error even in the ATT status.

Troubleshooting

•

shorted to positive: with key set to ON, disconnect the sensor connector and measure PIN

1 voltage on the cable harness side (grey cable): if there is voltage (5 or 12 V), restore the

cable harness; if there is not, replace the lambda probe

Lambda probe heating P0135

•

short circuit to positive/ open circuit, short circuit to negative

Error cause

•

If shorted to positive: excessive voltage has been detected at PIN 32 of the ENGINE con-

nector. If the circuit is open, shorted to negative: voltage equal to zero has been detected

at PIN 32 of the ENGINE connector. The instrument panel does not indicate the presence

of this error even in the ATT status.

Troubleshooting

Electrical system

DORSODURO 1200 ABS - ATC

ELE SYS - 154

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands

APRILIA DORSODURO 1200 ABS - ATC, Service Station Manual

Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands