APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download

Page: 297 / 408

•

Air temperature

3 - System safety checks

The checks are structured in several levels:

•

Level 1 - sensor correct operation

•

Level 2 - comparison between requested torque and estimated torque generated by the

engine

•

Level 3 - a microprocessor controls the correct operation of the regular microprocessor

The consequent maintenance operations may be of different gravity according to the level and the

defective component:

A the malfunction does not affect riding in safety, the warning light turns on, the word Service is dis-

played, the signal recovery value considered not reliable is used and the engine works regularly.

B the malfunction may affect riding in safety, the warning light turns on, the message Urgent Service is

displayed, the torque demands are not fully activated (reduced torque).

C the malfunction may affect riding in safety, the warning light turns on, the message Urgent Service

is displayed, the engine operates in Limp Home function (accelerated idle), the throttles which are at

the position exclusively depending on the springs are not moved. The engine may shut off during the

operation if it is running at idle speed and the gear is in neutral.

D the malfunction may affect riding in safety, the warning light turns on, the message Urgent Service

is displayed, the engine stops running.

Operating logic

Those riding motorbikes do not require a specific throttle valve opening from their engines but actually

a specific torque. The Ride by Wire system has been so designed that the throttles of the throttle bodies

are mechanically isolated from the throttle control; their actuation depends exclusively on 2 electrical

motors controlled by the control unit. The control unit refers to specific handle maps to determine by

how much and how quickly the throttle valves are opened. The parameters influencing the handle map

are as follows:

•

Handle aperture

•

Engine rpm

•

Handle aperture rate

The Marelli control unit performs the following functions:

1. Implements the necessary strategies for calculating torque demand

2. Operates the sensors and actuators necessary for system function

3. Safety checks for the Ride by Wire system

DORSODURO 1200 ABS - ATC

Power supply

P SUPP - 297

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands

APRILIA DORSODURO 1200 ABS - ATC, Service Station Manual

Search results

Summary of Contents for DORSODURO 1200 ABS - ATC

Reviews:

Related manuals for DORSODURO 1200 ABS - ATC

Brands by name

Popular brands