APRILIA DORSODURO 1200 ABS - ATC Service Station Manual Download | Manualshive

Page: 78 / 408

background image

TROUBLESHOOTING PROCEDURE IF THE EFI WARNING LIGHT ON THE INSTRUMENT PANEL

TURNS ON OR IF THERE IS ABNORMAL ENGINE PERFORMANCE

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

•

1 - THE "EFI" WARNING LIGHT IS ON AND THE WORD "SERVICE" IS SHOWN or THE

"EFI" WARNING LIGHT IS FLASHING AND THE WORDS "URGENT SERVICE" ARE

SHOWN or ONE OF THE TWO SITUATIONS TAKES PLACE AND IS SUDDENLY OUT or

THERE IS ABNORMAL ENGINE PERFORMANCE

•

2 - CONNECT THE DIAGNOSIS INSTRUMENT TO THE CONTROL UNIT SELECTING

"APRILIA, DORSODURO 1200, FUEL INJECTION"

•

3 - ARE CURRENT- "ATT"- or STORED- "MEM"- ERRORS SHOWN IN THE "ERRORS

DISPLAY" SCREEN PAGE?

YES, go to 4; NO, go to 11.

•

4 - IF THE ERROR IN THE CENTRAL WINDOW IS SELECTED AND "?" IS DISPLAYED,

PRESS THE KEY "?" TO OBTAIN FURTHER INFORMATION ABOUT THE ERROR. THEN

GO TO THE "ELECTRICAL SYSTEM/CHECKS AND CONTROLS" CHAPTER AND READ

THE INFORMATION CONCERNING THE DEFECTIVE COMPONENT

•

5 - ACCORDING TO WHAT IS INDICATED ABOUT THE ERROR/S, PROCEED AS SUG-

GESTED AND SOLVE THE PROBLEM

•

6 - WAS THE PROBLEM SOLVED BY REPLACING THE MARELLI CONTROL UNIT?

YES, go to 7; NO, go to 8.

•

7 - READ THE ACTIVATION PROCEDURE FOR A NEW CONTROL UNIT ON THE "ELEC-

TRICAL SYSTEM/CHECKS AND CONTROLS/ECU/MARELLI CONTROL UNIT" CHAP-

TER - END

•

8 - SELECT "ERROR CLEARING" FROM THE "DEVICES ACTIVATION (INJECTOR

ICON)" SCREEN PAGE

•

9 - WAS THE PROBLEM SOLVED BY REPLACING THE THROTTLE GRIP SENSOR

(DEMAND) OR THE THROTTLE BODY?

NO, END; YES, go to 10

•

10 - READ THE RESET PROCEDURE ON THE "ELECTRICAL SYSTEM/CHECKS AND

CONTROLS/THROTTLE GRIP POSITION SENSOR OR THROTTLE BODY" CHAPTER -

END

•

11 - CHECK IF THERE ARE CURRENT OR STORED ERRORS DETECTED BY THE IN-

STRUMENT PANEL REFERRING TO THE "DIAGNOSIS" CHAPTER, "INSTRUMENT

Troubleshooting

DORSODURO 1200 ABS - ATC

TROUBL - 78

Manuals by Motomatrix / www.motomatrix.co.uk / The Solution For Lost Motorcycle Coded Keys.

email: [email protected]

«
...
76
77
78
79
80
...
»

Summary of Contents for DORSODURO 1200 ABS - ATC

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for DORSODURO 1200 ABS - ATC

Brand: Yamaha Pages: 435

Brand: Bajaj Pages: 55

Brand: N-Com Pages: 2

Freeride 350 AUS

Brand: KTM Pages: 25

PowerCom INNOVA Plus Business

Brand: AKE Pages: 2

Brand: CRATONI Pages: 61

Brand: Cobra Pages: 80

Brand: Touratech Pages: 4

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 96

X-MAX 400 ABS 2018

Brand: Yamaha Pages: 118

Virago XV250T 2004

Brand: Yamaha Pages: 95

Brand: Yamaha Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands