Amazone UF 1002 Operating Manual Download Page 195

Page: 195 / 232

Cleaning, maintenance and repairs

UF02 BAG00225.3 09.22

195

14.6.7 Clean / exchange the filter in the hydraulic plug

Not with Profi-folding.

The hydraulic plugs are equipped with a filter (1)
that may block and then have to be cleaned / ex-
changed.

This is the case when the hydraulic functions run
slower.

1. Unscrew the hydraulic plug from the filter

housing.

2. Remove the filter with compression spring.

3. Clean / exchange the filter.

4. Re-fit the filter and compression spring cor-

rectly.

5. Screw back on the hydraulic plug. In doing

so, observe the correct seating of the O-ring
seal.

CAUTION

Danger of injuries from escaping
hydraulic oil at high pressure!

Work on the hydraulic system only in a
depressurized state.

Summary of Contents for UF 1002









































































































































































































































Search results

Summary of Contents for UF 1002

Reviews:

Amazone UF 1002, Operating Manual, Page: 195 / 232

Search results

Summary of Contents for UF 1002

Reviews: