Allen-Bradley 1756-M02AE User Manual Download Page 80

Page: 80 / 236

Chapter 3

Geometries with no orientation support

Rockwell Automation Publication MOTION-UM002F-EN-P - February 2018

Important:

Verify that the values for the link lengths, base offsets, and end-effector offsets are entered into the

Configuration

Parameters

dialog box using the same measurement units.

This example illustrates the typical configuration parameters for an Articulated
Dependent robot.

If the robot is two-dimensional, the X3b and X3e are X2b and X2e.

page 80

Base offsets for Articulated Dependent robot

page 81

End-Effector Offsets for Articulated Dependent robot

page 82

Link lengths are the rigid mechanical bodies attached at joints.

For an articulated dependent robot with

The length of

Is equal to the value of the distance between

2 dimensions

L1
L2

J1 and J2
J2 and the end-effector

3 dimensions

L1
L2

J2 and J3
J3 and the end-effector

Enter the link lengths on the

Geometry

tab in the

Coordinate System

Properties

dialog box.

Link lengths for Articulated
Dependent robot

Summary of Contents for 1756-M02AE













































































































































































































































Search results

Summary of Contents for 1756-M02AE

Reviews:

Allen-Bradley 1756-M02AE, User Manual, Page: 80 / 236

Search results

Summary of Contents for 1756-M02AE

Reviews: