manualshive.com logo in svg

Allen-Bradley 1756-M02AE, User Manual, Page: 160 / 236

Share
Download
Allen-Bradley 1756-M02AE User Manual Download Page 160

Chapter 4 

Geometries with orientation support 

 

160

 

Rockwell Automation Publication MOTION-UM002F-EN-P - February 2018 

Configure the joint limits   

Refer to robot manufacturer's data sheet to compute the range of J1, J2, and J6 
axes. These limits are set as a 

Soft Travel Limit 

on the 

Scaling

 tab in the 

Axis 

Properties

 dialog box. 

 

See also 

Identify the Work Envelope for Delta J1J2J6 robot

 on 

page 156

 

The work envelope for the 3-axis Delta robot relies on the Work and Tool Frame 

offset values defined in the MCTO instruction. The target end position range 
changes based on the Work and Tool Frame offsets. 

In the Delta robot, the End plate is always parallel to the Base plate and the 3-axis 
Delta robot can reach only up to limited orientation positions. Work and Tool 

frame offset values are limited up to reachable work envelope. The following offset 
values are allowed for Work and Tool frames. The MCTO instruction generates 

error 148 for invalid offset values. 

•

 

Offset values on X, Y, Z and Rz axis are allowed for the Work Frame offsets. 

Rx and Ry offsets are restricted and must be set to 0°. Specify these offset 
values through the 

WorkFrame

 parameter in the MCTO instruction.   

•

 

Offset values on X, Y, Z and Rz axis are allowed for the Tool Frame offsets. 
Rx and Ry offsets are restricted and must be set to 0°. Specify these offset 

values through the 

ToolFrame

 parameter in the MCTO instruction. 

See also 

Identity the Work Envelope

 on 

page 156

 

The End of Arm (EOA), using the default work and tool frame settings, can be 

Work and Tool Frame offset 
limits for Delta J1J2J6 robot 

Invalid Cartesian positions 

Summary of Contents for 1756-M02AE













































































































































































































































Reviews:

No comments