ALDI ABP1815MA Instruction Manual Download Page 164

Page: 164 / 168

AFTER SALES SUPPORT

1300 889 028 (toll free)

MODEL No.:

ACG118PA • 2323 • 05/2019

e-mail:

[email protected]

below 0

C, or above 40

10. Disconnect from your equipment when not charging or the

charging is over.

6. Important information – Product care

NOTE:

For any issuses related directly to your Battery, contact the

Customer Service of the manufacturer as listed on the battery

packaging, manual or on the label on the battery.

This Charger uses Lithium Ion Battery Cells. Care MUST be taken to

ensure both the safety and life of the pack is maintained. Ensure you

have read all of the safety notes in the previous pages before using

the Charger.

Treat the battery pack with care and within the guidelines of this

manual.

If the battery pack does become immersed in water or any fluids,

or is subject to a severe drop or it does not operate within the

guidelines of this manual or the supplied manual, immediately STOP

using the battery pack and have it checked.

7. Operation

7.1. To install or remove the battery pack

To install the battery pack

Slide the fully charged battery pack (4) onto the USB Charger with

sufficient force until it clicks into position.

To remove the battery pack

Depress the battery pack release button (6) firmly, then slide the

battery pack (4) out away from the USB charger.

NOTE:

Remove the USB charger from the battery pack (4) when not

in use.

7.2. USB Charging Ports (6)

The USB charger is equipped with 2 USB charging ports (3) and

delivers 2.0 A total current per USB port.

Summary of Contents for ABP1815MA









































































































































































Search results

Summary of Contents for ABP1815MA

Reviews:

Related manuals for ABP1815MA

Brands by name

Popular brands

ALDI ABP1815MA, Instruction Manual

Search results

Summary of Contents for ABP1815MA

Reviews:

Related manuals for ABP1815MA

Brands by name

Popular brands