ALDI ABP1815MA Instruction Manual Download Page 88

Page: 88 / 168

AFTER SALES SUPPORT

1300 889 028 (toll free)

e-mail:

[email protected]

CSC165XA.9 • 2323 • 05/2019

MODEL No.:

CSC165XA.9 • 2323 • 05/2019

previous pages before using the 20V Li-Ion 165mm Circular Saw.

Treat the battery pack with care and within the guidelines of this

manual.

If the battery pack does become immersed in water or any fluids,

or is subject to a severe drop or it does not operate within the

guidelines of this manual or the supplied manual, immediately STOP

using the battery pack and have it checked.

7. Assembly

NOTE:

Before using the tool, read the instruction manual

carefully.

7.1 To remove the battery pack (See Fig. A1)

Depress the battery pack release button (17) firmly, then slide the

battery pack (16) out away from the tool.

7.2 To install the battery pack (See Fig. A2)

Slide the fully charged battery pack (16) onto the tool with

sufficient force until it clicks into position.

Summary of Contents for ABP1815MA









































































































































































Search results

Summary of Contents for ABP1815MA

Reviews:

Related manuals for ABP1815MA

Brands by name

Popular brands

ALDI ABP1815MA, Instruction Manual

Search results

Summary of Contents for ABP1815MA

Reviews:

Related manuals for ABP1815MA

Brands by name

Popular brands