ALDI ABP1815MA Instruction Manual Download Page 65

Page: 65 / 168

AFTER SALES SUPPORT

1300 889 028 (toll free)

MODEL No.:

CID180XA.9 • 2323 • 05/2019

e-mail:

[email protected]

8.5 Belt Clip (4) (See Fig. G)

The side belt clip (4) is used to assist to clip the Impact Driver to

your waist belt while working. To install, insert the assembly screw

through the belt clip screw hole into the retaining hole on the

Impact Driver, and using a philips head screwdriver (not supplied),

tighten the screw by turning in a clockwise direction

NOTE:

The belt clip (4) can be assembled onto either side of the

Impact Driver.

IMPORTANT:

When attaching or replacing the belt clip (4), use only

the assembly screw that is provided. Be sure to securely tighten

screw.

8.6 Overload Protection

When in overload condition, the motor will come to a stop. Reduce

the load on the machine immediately and allow to cool for approx.

30 seconds at the highest no-load speed.

8.7 Temperature Cut Out

If the Impact Driver is constantly overloaded, or the Impact Driver is

used constantly at maximum rating in high ambient conditions, the

battery cells may overheat causing the battery pack to shut down.

When this occurs you will need to allow the battery cells to cool.

NOTE:

The Impact Driver will not restart until the battery pack has

cooled.

To reduce the temperature of the cells remove the battery pack

from the Impact Driver and place the battery pack in a free air

Summary of Contents for ABP1815MA









































































































































































Search results

Summary of Contents for ABP1815MA

Reviews:

Related manuals for ABP1815MA

Brands by name

Popular brands

ALDI ABP1815MA, Instruction Manual

Search results

Summary of Contents for ABP1815MA

Reviews:

Related manuals for ABP1815MA

Brands by name

Popular brands