3Com 5000/6000 Quick Reference Manual Download Page 141

Page: 141 / 162

3Com Router 5000/6000 Family

141

Command Reference

sot sdlc-status primary

Use the

sot sdlc-status primary

command to set the role of the router to SDLC primary node.

Synchronous Serial Interface view

sot sdlc-status secondary

Use the

sot sdlc-status secondary

command to set the role of the router to SDLC secondary node.

Synchronous Serial Interface view

sot send address

Use the

sot send address

command to configure the route for sending SDLC frames to the specified

specific terminal.

Synchronous Serial Interface view

sot send all tcp

Use the

send all tcp

command to forward all received SDLC frames to the specified address.

Synchronous Serial Interface view

sot timer keepalive

Use the

sot timer keepalive

command to configure the keepalive timer.

System view

source

Use the

tunnel source

command to specify the source IP address or source interface to be filled in the

added IP header at the time of tunnel interface encapsulation.

Tunnel Interface view

source-interface

Use the

source-interface

command to configure the source interface in the transmitted test packets.

HWPing Test Group view

source-ip

Use the

source-ip

command to configure a source IP address for this test.

HWPing Test Group view

source-ip

Use the

source-ip

command to bind a source IP address to the router when it functions as a User Agent

(UA).

SIP Client view

source-policy

Use the

source-policy

command to configure a router to filter the multicast data packet received according

to source (group) address.

PIM view

source-port

Use the

source-port

command to configure a source port number for this test.

HWPing Test Group view

special-character

Use the

special-character

command to configure the supported special characters during register signal

exchange.

R2 CAS view

special-service

Use the

special-service

command to enable or disable the special-service numbers.

Voice Dial Program view

speed

Use the

speed

command to set the operating speed of the Ethernet interface.

Ethernet Interface view

speed

Use the

speed

command to configure the rate of the port.

Ethernet Port view

speed

Use the

speed

command to set the transmission rate on the user interface.

User Interface view

spf-delay-interval

Use the

spf-delay-interval

command to configure the interval for actively releasing CPU in the SPF

calculation.

IS-IS view

Summary of Contents for 5000/6000



































































































































































Search results

Summary of Contents for 5000/6000

Reviews:

Related manuals for 5000/6000

Brands by name

Popular brands

3Com 5000/6000, Quick Reference Manual

Search results

Summary of Contents for 5000/6000

Reviews:

Related manuals for 5000/6000

Brands by name

Popular brands