York 160.87-OM1 Скачать руководство пользователя

Страница: 150 / 268

Table 144: Display only

Field/LED name

Description

Leaving Chilled Liquid

Temperature

Displays the temperature of the liquid as it leaves the evaporator.

Leaving Chilled Active

Setpoint

Displays the setpoint to which the Leaving Chilled Liquid is being

controlled.

Quick Pulldown in Effect

(LED)

Illuminates while a Quick Pulldown is in effect. This is in effect from

a start initiate until the Quick Pulldown Setpoint Offset has been

reached or the Pulldown Override Time has elapsed, whichever

occurs first.

Note:

For fields requiring access level of SERVICE. Qualified service technicians should refer

to the OptiView Control Center Service for operation instructions and explanations of all

programmable setpoints and displayed values.

Table 145: Programmable

Button

Access level Description

Change

Setpoints

Service

Used to enter the following setpoints.

Pressing this key places a green selection box around the first

changeable setpoint. Use the ▲ and ▼ keys to place the selection

box around the desired setpoint. With the setpoint selected, press

the Enter key. A dialog box appears with the range of settings.

Mapping

Enable

Service

This is the same setpoint as shown on the ACC DETAILS Screen.

It can be programmed on either the ACC Screen or the QUICK

START Screen. It sets the Delta T needed to be met to enable surge

mapping and speed reduction initially on startup. (0.5°F to 4.0°F;

default 1.0°F)

Pulldown

Override

Time

Service

This setpoint is the length of time the PRV is held open (Quick

Restart) and the ACC speed (Quick Restart and Quick Normal Start)

is increased on startup if the Quick Pulldown Setpoint Offset is not

reached.

This could be due to hitting current limit during the pulldown. If

the Quick Pulldown Setpoint Offset is not reached in the Pulldown

Override Time, PRV and ACC speed control will revert back to normal

automatic control. (0 min to 15 min; default 10 min)

VSD Start

Frequency

Service

The VSD Start Frequency is as follows:

•

60 Hz units with quick start enabled equal 30 Hz to 45 Hz

(default 45 Hz)

•

50 Hz units equal 25 Hz to 37.5 Hz (default 37.5 Hz)

This setpoint is the same as shown on the ACC DETAILS Screen. It

can be programmed on either the ACC Screen or the QUICK START

Screen. It sets the VSD Start Frequency from which the speed will

ramp from.

YK-EP Style B Centrifugal Chiller

150

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды