York 160.87-OM1 Скачать руководство пользователя

Страница: 210 / 268

•

Evaporator Refrigerant Temperature (RT7) has been enabled by a Service Technician using

instructions in

OptiView Control Center – Service Instructions (Form 160.54-M1)

•

Not in Brine Cooling mode

•

Smart Freeze is enabled.

•

Evaporator Temperature Sensor (RT7) or Evaporator Saturation Temperature is indicating a

temperature of less than 32.0°F

The chiller can be started after the temperatures are within 3.0°F of one another and the Operator

presses the WARNING RESET button.

Condenser – High Pressure Contacts Open

The contacts of the electro-mechanical high pressure safety device, located on the condenser shell,

have opened because this device has detected a pressure:

•

more than 204 PSIG (R134a)

The contacts will automatically close when the condenser pressure decreases to:

•

less than 160 PSIG (R134a)

The chiller can be started after the contacts close and the Operator presses the WARNING RESET

button.

Condenser – High Pressure

The condenser pressure, as sensed by the Condenser transducer, has increased to:

•

more than 180.0 PSIG (R134a)

•

more than 265.0 PSIG (R22)

The chiller can be started after the pressure decreases to:

•

less than 120.0 PSIG (R134a)

•

less than 205 PSIG (R22) and the Operator presses the WARNING RESET button.

For special order R134a high condenser temperature chiller applications, the Condenser

Temperature Range Setpoint is set to Extended. The trip/reset threshold is then 200/140 PSIG.

Condenser – High Pressure – Stopped

The condenser pressure exceeded 160.0 PSIG (R134a), 240.0 PSIG (R22) while the chiller was

stopped. High temperature condenser water flowing through the condenser while the chiller is

shutdown can cause a condenser high pressure condition resulting in loss of refrigerant. This safety

fault anticipates this problem by annunciating the condenser high pressure condition. The chiller

can be restarted after a Service Technician performs a special reset preset procedure contained in

OptiView Control Center – Service Instructions (Form 160.54-M1)

For special order R134a high condenser temperature chiller applications, the Condenser

Temperature Range Setpoint is set to Extended. The trip/reset is then 170/170 PSIG .

Condenser – Pressure Transducer Out Of Range

The Condenser Pressure transducer is indicating a pressure that is:

•

less than 6.8 PSIG (R134a)

•

less than 24.2 PSIG (R22)

•

or more than 300.0 PSIG (R134a or R22)

YK-EP Style B Centrifugal Chiller

210

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды