York 160.87-OM1 Скачать руководство пользователя

Страница: 57 / 268

Hot gas bypass screen

Figure 19: Hot gas bypass screen

This screen displays a cutaway view of the Hot Gas Bypass Valve. The setpoints relating to the

Hot Gas Bypass Control are maintained on this screen. Related Hot Gas control parameters are

displayed for reference. The Hot Gas Valve can be manually controlled from this screen. Through

animation, the relative valve position is displayed. The parameters displayed on this screen vary

according to the software version and the selection made for the Motor Communications Protocol

Setpoint when equipped with Variable Speed Drive (VSD) or Medium Voltage Variable Speed Drive

(MVVSD).

Table 43: Display only

Field/LED name

Description

Valve Position

Displays the present position of the Hot Gas Valve as a value

between 0% (closed) to 100% (full open). By animation, the valve is

shown in its relative position. The actual position of the valve does

not match the percentage displayed in the Valve Position Box. The

actual levels and their relative values can be read from Table 44.

Pre-Rotation Vanes Position Displays the present Pre-Rotation Vanes position as a value between

0% (closed) and 100% (full open).

Delta P/P

Displays the chiller head pressure calculated as (condenser pressure

– evaporator pressure/evaporator pressure).

Temperature Differential

(LCHLT – Setpoint)

Displays the difference between the Leaving Chilled Liquid

Temperature and the Leaving Chilled Liquid Temperature Setpoint.

YK-EP Style B Centrifugal Chiller

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды