York 160.87-OM1 Скачать руководство пользователя

Страница: 32 / 268

Table 14: Programmable

Button

Access level Description

Local Leaving

Chilled Liquid

Temperature

– Setpoint

Operator

This value allows the user to define the Leaving Chilled Liquid

Temperature that is to be maintained by the chiller. It is

programmable over the range of 38.0°F to 70.0°F (water) or 10.0°F

to 70.0°F (brine). If Smart Freeze is enabled, the range is 36.0°F to

70.0°F (water). A remote device can provide an analog signal (0

to 20mA, 4 to 20mA, 0 to 10VDC or 2 to 10VDC) in Analog Remote

mode, or PWM signal in Digital Remote mode that changes the

setpoint by creating an offset above the operator programmed

BASE Leaving Chilled Liquid Temperature Setpoint. This offset may

be defined as 10, 20, 30, or 40°F above the BASE Setpoint (refer

to the Leaving Chilled Liquid Temperature Setpoints – Setpoint

description). Additionally, an E-Link or SC-Equip Gateway (in ISN

Remote mode) can define the setpoint through a serial data stream.

In this case, the incoming setpoint is not an offset that is applied

to the locally programmed BASE Setpoint value, but rather is the

setpoint value itself.

Leaving

Chilled Liquid

Temperature

Cycling

Offset –

Shutdown

Operator

This value allows the user to specify the Leaving Chilled Liquid

Temperature at which the chiller will shut down on a LEAVING

CHILLED LIQUID – LOW TEMPERATURE cycling shutdown. This

is done by defining an offset below the Leaving Chilled Liquid

Temperature Setpoint. It is programmable over a range of 1°F

to 64°F below the setpoint, to a minimum cutout of 36°F (water),

34°F (water with Smart Freeze enabled) or 6°F (brine). Anytime

the Leaving Chilled Liquid Temperature Setpoint is increased, the

setpoint is increased at a rate of 0.2°F per second to allow the chiller

time to unload*.

Leaving

Chilled Liquid

Temperature

Cycling

Offset –

Restart

Operator

This value allows the user to specify the Leaving Chilled Liquid

Temperature at which the chiller will restart after a shutdown on a

LEAVING CHILLED LIQUID – LOW TEMPERATURE cycling shutdown.

This is done by defining an offset above the Leaving Chilled Liquid

Temperature Setpoint. It is programmable over a range of 0°F to

70°F above the setpoint, to a maximum restart value of 80°F. The

chiller will automatically restart when this temperature is reached.

This setpoint can be used to reduce chiller cycling by delaying the

chiller restart until the cooling load has increased.

Note:

* The offset being used is displayed as Effective Offset in the upper right area of the

display. Usually, the Offset used is the same as the value programmed for the Shutdown

Setpoint. However, the Offset being used will automatically change based on the values

programmed for the Leaving Chilled Liquid Temperature Setpoint and the Shutdown Setpoint,

to prevent the Leaving Chilled Liquid Temperature from going below the minimum allowed

value: 36°F (water), 34°F (water with smart freeze enabled) or 6°F (brine). For example, if the

Leaving Chilled Liquid Temperature Setpoint is set to 45°F (water) and the Shutdown Setpoint

is set to 4°F, the Effective Offset is displayed as 4°F. If the leaving setpoint is lowered to 38°F,

the Effective Offset will change to 2°F. If the leaving chilled setpoint is raised back to 45°F, the

Effective Offset will revert back to the Shutdown Setpoint.

YK-EP Style B Centrifugal Chiller

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды