York 160.87-OM1 Скачать руководство пользователя

Страница: 193 / 268

Warning – Evaporator – Low Pressure Limit

The Evaporator Pressure has decreased to the Warning threshold. This threshold is fixed in Water

cooling applications. In Brine cooling applications, the threshold is a fixed amount above the

programmable safety shutdown threshold. The Safety threshold in Brine applications is determined

by the Brine solution and is determined by the YORK Factory. While this condition is in effect, the

Pre-Rotation Vanes are inhibited from further opening. This message automatically clears and the

Vanes are permitted to open when the Evaporator Pressure increases to the reset value.

Table 198: Warning and reset thresholds

Warning threshold (PSIG)

Reset threshold (PSIG)

Water

Brine

Water

Brine

R22

56.2

+1.9 more than Safety Setpoint

57.5

+3.2 more than Safety Setpoint

R134a

27.0

+2.0 >Safety Setpoint

28.0

+3.0>Safety Setpoint

Warning – Vanes Uncalibrated – Fixed Speed

The Compressor Motor Variable Speed Drive (VSD) is operating Fixed Speed (full speed) mode

because the Pre-Rotation Vanes position potentiometer calibration has not been performed.

Warning – Harmonic Filter – Operation Inhibited

The Compressor Motor Variable Speed Drive (VSD) Harmonic Filter has been inhibited. Refer to

Variable Speed Drive – Service Instructions (Form 160.00-M1)

. Harmonic Filter operation should not be

altered by anyone other than a qualified Service Technician.

Warning – Harmonic Filter – Data Loss

Communications between the Harmonic Filter Logic Board and the Compressor Motor Variable

Speed Drive VSD Logic Board or the Adaptive Capacity Control Board is not occurring. While this

condition exists, all filter related parameters are displayed as X’s. This message automatically clears

when communications are restored.

Warning – Harmonic Filter – Input Frequency Range

The power line frequency detected by the Compressor Motor Variable Speed Drive (VSD) Harmonic

Filter is outside the range of 58 to 62 Hz (60 Hz), or 49 to 51 Hz (50 Hz). While this condition exists,

all filter related parameters are displayed as X’s. This message automatically clears when the line

frequency is within range.

Warning – Harmonic Filter – Not Running

This warning is set when all of the following are true for 20 continuous seconds:

•

Chiller is running

•

Filter is enabled

•

Filter present status is true

•

Run Time greater than 20 seconds

•

Filter operating mode is stopped

This warning is released when the chiller is stopped, but will be displayed until manually cleared

using the WARNING RESET key when logged in at OPERATOR (or higher) access level.

Warning – Vanes Uncalibrated

The Hot Gas Bypass feature is enabled, but the Pre-Rotation Vanes calibration procedure has not

yet been performed.

193

YK-EP Style B Centrifugal Chiller

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды