York 160.87-OM1 Скачать руководство пользователя | Manualshive

Страница: 60 / 268

background image

Surge protection screen

Figure 20: Surge protection screen

This screen displays a cutaway view of the chiller compressor and all parameters relating to the

Surge Protection feature. All setpoints relating to this screen are maintained on this screen.
The Surge Protection feature detects surge events and provides a running count of the surges

detected over the lifetime of the chiller. It allows the user to define how many surges are excessive

and how the control will react to an excess surge condition. When excess surging is detected, it

can be configured to shutdown the chiller, or initiate a surge avoidance mode while allowing it to

continue to run or simply display a warning message. The sensitivity of this surge detection is set

by the Sensitivity Setpoint on this screen. The surges detected by this feature are also used for the

Hot Gas Bypass feature (Refer to

Hot gas bypass screen

).

The detection and counting of surges in this feature is completely independent of the surge

detection/counting performed by the Variable Speed Drive (VSD) Adaptive Capacity Control (ACC)

Surge Detection. The ACC Surge Detection creates a surge map used to control the speed of the

drive. The ACC Surge Detection is performed in the Microboard

Table 47: Display only

Field/LED name

Description

Delta P/P

A parameter that represents the system differential or Head

Pressure. It is calculated as (condenser pressure – evaporator

pressure) / evaporator pressure.

Surge Avoidance Surge

Detected (LED)

Illuminates momentarily when a surge is detected by the Surge

Protection feature. If equipped with a VSD or MVVSD these are

only the surges detected while the drive is running at maximum

frequency.

Surge Avoidance Surge

Count

This is the total number of surges accumulated by the Surge

Protection feature. If equipped with a VSD or MVVSD, it is only the

surges detected while the drive is running at maximum frequency.

YK-EP Style B Centrifugal Chiller

60

«
...
58
59
60
61
62
...
»

Содержание 160.87-OM1













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 160.87-OM1

Бренд: Zip Страницы: 12

Millenium YK D Series

Бренд: York Страницы: 28

Millennium YCAR 0100SC

Бренд: York Страницы: 24

Бренд: Nordcap Страницы: 12

Бренд: TECO Страницы: 7

Attila 10 TRAYS

Бренд: Tecnodom Страницы: 144

Бренд: Troy-Bilt Страницы: 32

Бренд: Troy-Bilt Страницы: 32

Бренд: Troy-Bilt Страницы: 64

Бренд: Hiniker Страницы: 61

Бренд: Texas Страницы: 54

Бренд: Daikin Страницы: 16

Бренд: Laird Страницы: 2

Бренд: Nemox Страницы: 33

Бренд: Bluebird Страницы: 36

Бренд: Bluebird Страницы: 44

MGD-15W-MGD-ADV-02

Бренд: Advantage Страницы: 80

Бренд: Yard Machines Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды