manualshive.com logo in svg

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
York 160.87-OM1 Скачать руководство пользователя страница 63

Table 48: Programmable

Button

Access level Description

Surge

Sensitivity

Service

Allows the user to define the surge detection sensitivity of the

Surge Protection feature. The Surge Sensitivity Setpoint on the

ACC DETAILS Screen sets the sensitivity of the ACC Surge Detection

feature that is employed for ACC Surge Detection. Selectable over

the range of 0.3 to 1.3; default 0.3. The smaller the number, the

greater the sensitivity.

Note: 

*

When an Excess Surge situation is detected, the action depends upon the following:

•

If both the Shutdown and Extended Run Setpoints are Disabled, the chiller will continue

to run, displaying the message WARNING – EXCESS SURGE DETECTED. Refer to Hot

Gas Bypass and Variable Speed Drive exceptions. See 

Shutdown (Enabled/Disabled)

 and

Extended Run (Enabled/Disabled) 

 in Table 48.

•

If the Shutdown Setpoint is Enabled and the Extended Run Setpoint is Disabled, the

chiller will perform a safety shutdown and display Surge Protection – Excess Surge. Refer

to Hot Gas Bypass and Variable Speed Drive exceptions. See 

Shutdown (Enabled/ Disabled)

and 

Extended Run (Enabled/Disabled)

 in Table 48.

•

If the Shutdown Setpoint is Disabled and the Extended Run Setpoint is Enabled, the Pre-

Rotation Vanes are driven closed for 10 minutes and WARNING – SURGE PROTECTION

– EXCESS SURGE LIMIT is displayed. When the 10 minutes have elapsed, if the Surge

Window Count is less than or equal to the Count Limit, this message and load inhibit

are automatically cleared. Alternating with this message is WARNING – EXCESS SURGE

DETECTED that continues after the 10 minute period has elapsed until manually cleared

with the WARNING RESET key. Refer to Hot Gas Bypass and Variable Speed Drive

exceptions. See 

Shutdown (Enabled/Disabled)

 and 

Extended Run (Enabled/Disabled)

 in Table

48.

•

If both the Shutdown and Extended Run Setpoint are Enabled, the 10 minute Extended

Run mode is invoked as described above. However, if the Surge Window Count exceeds

the Count Limit at the completion of the 10 minute Extended Run period, a safety

shutdown is performed and Surge Protection – Excess Surge is displayed. Refer to Hot

Gas Bypass and Variable Speed Drive exceptions. See 

Shutdown (Enabled/Disabled)

 and

Extended Run (Enabled/Disabled)

 in Table 48.

Table 49: Navigation

Button

Access level Description

Home

View

Returns user to HOME Screen.

Compressor View

Returns user to COMPRESSOR Screen.

63

YK-EP Style B Centrifugal Chiller

Содержание 160.87-OM1













































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды