York 160.87-OM1 Скачать руководство пользователя

Страница: 31 / 268

Table 13: Display only fields

Field/LED name

Description

Leaving Chilled Liquid

Temperature Setpoints –

Setpoint

Displays the present setpoint to which the chiller is operating,

whether controlled locally or remotely.

Leaving Chilled Liquid

Temperature Setpoints –

Shutdown

Displays the Leaving Chilled Liquid Temperature at which the chiller

will shutdown on Leaving Chilled Liquid – Low Temperature. This

temperature is entered as an offset with the Leaving Chilled Liquid

Temperature Cycling Offset – Shutdown Setpoint below. Although

the offset setpoint is changed manually, the offset being used

can change automatically to prevent the Leaving Chilled Liquid

Temperature from going below the minimum allowed value: 36°F

(water), 34°F (water with smart freeze enabled) or 6°F (brine). The

offset being used is displayed as Effective Offset.

Leaving Chilled Liquid

Temperature Setpoints –

Restart

Displays the Leaving Chilled Liquid Temperature at which the chiller

will restart after it has shutdown on LEAVING CHILLED LIQUID –

LOW TEMPERATURE cycling shutdown. This temperature is set as an

offset using the Leaving Chilled Liquid Temperature Cycling Offset –

Restart Setpoint, displayed as OFFSET adjacent to this value.

Table 14: Programmable

Button

Access level Description

Smart Freeze

(Off / On)

Service

This value is only available if the chiller is not in Brine mode. It

allows the user to enable the Smart Freeze Point Operation which

allows the chiller to run closer to the freeze point without shutting

down.

Brine Low

Evaporator

Cutout

Service

This value is only available in Brine mode. It allows the user to

specify the Evaporator Pressure at which a safety shutdown is

initiated.

Refrigerant

(Enabled /

Disabled)

Service

When an Evaporator Refrigerant Sensor has been installed it must

be enabled via this toggle before the system will utilize the new,

enhanced resolution input.

Local Leaving

Chilled Liquid

Temperature

– Range

Operator

This is the range over which an analog (0 to 20mA, 4 to 20mA, 0 to

10VDC or 2 to 10VDC) in Analog Remote mode or a digital signal

(PWM) in Digital Remote mode can reset the Leaving Chilled Liquid

Temperature Setpoint above the operator programmed BASE

Setpoint. Programmable as 10, 20, 30 or 40°F. It is added to the BASE

value to create a range over which the remote device can reset the

setpoint. For example, if this setpoint is programmed for 10°F and

the operator programmed value is 45°F, then the remote device can

set the Leaving Chilled Liquid Temperature Setpoint over the range

of 45.0° to 55.0°F.

YK-EP Style B Centrifugal Chiller

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды