York 160.87-OM1 Скачать руководство пользователя

Страница: 165 / 268

Table 165: Programmable

Button

Access level Description

Flow Switch

Service

Used to enter the applicable flow switch type. Paddle-type (TB4) or

Thermal-Type (J14) Flow sensors.

Hot Gas

Control

(Enabled/

Disabled)

Service

Enables and disables the optional Hot Gas Bypass Control feature.

VGD

(Enabled/

Disabled)

Service

Enables and disables the Variable Geometry Diffuser feature. If

equipped with this feature, it should be enabled. Otherwise, it

should be disabled.

Chiller Style/

Compressor Service

Automatically set to Style G/K6-7 Com

Edit Phone

Numbers

Service

Displays up to two service phone numbers. The Regional service

phone number is displayed as the first number. Although the

label and number can be changed appropriately, the default for

this entry is “Johnson Controls North American Toll Free Number

1-800-861-1001”. The Local service phone number is displayed as

the second number. Although blank by default, the appropriate

label and number can be entered by a Service Technician.

Table 166: Navigation

Button

Access level Description

Home

View

Returns user to HOME Screen.

Setup

View

Returns user to SETUP Screen.

165

YK-EP Style B Centrifugal Chiller

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды