York 160.87-OM1 Скачать руководство пользователя | Manualshive

Страница: 214 / 268

background image

Watchdog – Software Reboot

The Microboard’s software Watchdog initiated a Microprocessor reset because it detected that a

portion of the chiller operating program was not being executed. The result of this reset is a safety

shutdown and re-initialization of the program. This is generally indicative of a severe electrical

power disturbance or impending Microboard Failure. The chiller can be started after the Operator

presses the WARNING RESET button.

Surge Protection – Excess Surge

(Applies only if Surge Protection Shutdown feature is Enabled)
The Surge Window Count surge events exceeded the Count Limit Setpoint. If the Surge Protection

Extended Run feature is Disabled, the chiller shuts down as soon as the count exceeds the limit. If

the Extended Run feature is Enabled, this shutdown occurs only if the count exceeds the limit at

completion of the 10 minute Extended Run period. The chiller can be started after the Operator

presses the WARNING RESET button.

Motor – Lack of Bearing Lubrication

The Operating Hours Since Last Motor Lubrication has exceeded set hours. This message replaces

WARNING MOTOR BEARING LUBE REQUIRED above. This safety shutdown remains in effect until

the Operator presses the WARNING RESET button and enters his/her initials, name or user ID in

OPERATOR access level (or higher) using the MOTOR LUBE ACKNOWLEDGE key on the MOTOR

LUBRICATION Screen. Refer to the

Motor lubrication screen

for entry instructions. The date and

time of this entry is automatically logged as the Date Of Last Motor Lubrication and Time Of Last

Motor Lubrication. It also resets the Operating Hours Since Last Lubrication to zero.
The date this warning occurs is stored as the Date Of Last Motor Lubrication Warning Or Fault.

This message will only be displayed if the Auto Lube Setpoint is disabled. With this setting, if the

Shutdown Setpoint is enabled, this safety shutdown will occur. If shutdown is disabled, this warning

message will be displayed but the safety shutdown will not be performed.

Motor – High Winding Temperature

This safety shutdown occurs when either of the following conditions are present:

•

Any of the enabled Motor Winding Temperatures exceeded the programmed High Winding

Temperature Shutdown threshold plus the programmed Winding Hotspot Allowance

threshold for 3 continuous seconds.

-OR-

•

The Average Winding Temperature has exceeded the programmed High Winding

Temperature Shutdown threshold for 3 continuous seconds.

The values programmed for the above safety thresholds are displayed as High Winding

Temperature Shutdown and Winding Hotspot Allowance on the MOTOR SETPOINTS Screen. They

are programmed with the Winding Setup Setpoint on that screen. The chiller can be started after

all winding temperatures decrease to at least 18°F (10°C) below the shutdown threshold and

the Operator presses the WARNING RESET button. This safety shutdown will not occur when the

Winding Temperature Protection Setpoint is set to Disabled on the MOTOR DETAILS Screen. Also,

it will not act on any RTD input registering as an open RTD or any individual winding temperature

sensor that has been disabled with the Temperature Disable Setpoint on the MOTOR SETPOINTS

Screen.

YK-EP Style B Centrifugal Chiller

214

«
...
212
213
214
215
216
...
»

Содержание 160.87-OM1













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 160.87-OM1

Бренд: McQuay Страницы: 20

Бренд: Land Pride Страницы: 24

Millennium YCAR 0100SC

Бренд: York Страницы: 24

Бренд: Garland Страницы: 180

Бренд: Jensen Страницы: 110

DR CHIPPER C123E-CHP

Бренд: Country Home Products Страницы: 32

Бренд: York Страницы: 104

Бренд: Craftsman Страницы: 69

Бренд: Craftsman Страницы: 20

Бренд: xtra Страницы: 20

Бренд: L.T. Rich Products Страницы: 31

Бренд: Texas Страницы: 37

Бренд: Texas Страницы: 36

Бренд: Texas Страницы: 49

Бренд: Texas Страницы: 64

Бренд: PowerTek Страницы: 7

Бренд: Western Страницы: 44

Бренд: Cavecool Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды