York 160.87-OM1 Скачать руководство пользователя страница 149

Страница: 149 / 268

Quick start screen

Figure 51: Quick start screen

The Quick Start feature is useful in data center and process control applications where it is

desirable to re-establish cooling as fast as possible after a shutdown or power failure. This feature,

when enabled, allows quicker starts and restarts than normal control. It does this by reducing

the time cycle for chiller restart and once running, loading the chiller as fast as possible. After the

chiller is running and has met a specified setpoint or a specified period of time has elapsed, control

returns to normal.
Quick Start feature has two different start modes:

•

Quick Restart – When the chiller shuts down, if certain conditions are met at the completion

of coastdown (and within 30 seconds thereafter), the VSD is started immediately with no

prelube. The vanes are given a constant open pulse and after the VSD achieves its start

frequency, the speed ramp rate is faster than with normal control.

•

Quick Normal Start – If the conditions for a Quick Restart are not met, the next time the

chiller is started, it has a prelube period just like a normal start, however the vanes will begin

to open at the beginning of prelube, instead of waiting until System Run. At the completion

of prelube, the VSD is started and after the VSD achieves its Start Frequency, the speed ramp

rate is faster than with normal control.

In order to use this feature, the chiller must be equipped with a Variable Speed Drive in Modbus

Protocol Configuration or a Medium Voltage Variable Speed Drive. The low inrush current of a VSD

allows more starts per hour and allows the chiller to start with a more open vane position. It must

be enabled on the Setpoints Screen with an ADMIN password by a qualified Service Technician.

Once enabled, all setpoints and parameters related to this feature are displayed on this screen,

when logged in at SERVICE access level.

149

YK-EP Style B Centrifugal Chiller

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Бренды по названию

Популярные бренды