York 160.87-OM1 Скачать руководство пользователя страница 79

Страница: 79 / 268

Oil sump screen

Figure 27: Oil sump screen

This screen displays a close-up of the chiller oil sump and provides all the necessary setpoints for

maintaining the Variable Speed Oil Pump (VSOP). In addition, this screen allows manual control of

the frequency command sent to the VSOP.

Table 68: Display only

Field/LED

name

Access level Description

Oil Pressure

–

Displays the pressure differential between the high side oil

pressure transducer (output of oil filter) and the low side oil

pressure transducer (compressor housing). The displayed value

includes offset pressure derived from auto-zeroing during the

System Prelube. (Refer to explanation of auto-zeroing in

Primary

compressor screen

). If either of the transducers used to calculate

this differential is out of range, the display field will show XX.X.

Oil Sump

Temperature

–

Displays the temperature of the oil in the sump.

Oil –

Saturated

Condenser

Temperature

Differential

–

(Variable Speed Oil Pump Only) Displays the difference between the

Oil Sump Temperature and the Saturated Condenser Temperature.

This parameter is useful when analyzing oil heater operation since it

is used in the control of the oil heater.

Pump Oil

Pressure

(HOP)

–

Displays the high side oil pressure measured at the compressor

bearing input.

YK-EP Style B Centrifugal Chiller

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Бренды по названию

Популярные бренды