York 160.87-OM1 Скачать руководство пользователя

Страница: 30 / 268

Evaporator screen

Figure 9: Evaporator screen

Table 13: Display only fields

Field/LED name

Description

Chilled Liquid Flow Switch

(Open / Closed)

Displays whether the liquid flow is present in the evaporator.

Chilled Liquid Pump

Displays the command presently sent by the Control Center to the

Chilled Liquid Pump (RUN or STOP).

Evaporator Pressure

Displays the present refrigerant pressure in the evaporator.

Evaporator Saturation

Temperature

Displays the present saturation temperature in the evaporator.

Return Chilled Liquid

Temperature

Displays the temperature of the liquid as it enters the evaporator.

Leaving Chilled Liquid

Temperature

Displays the temperature of the liquid as it leaves the evaporator.

Evaporator Refrigerant

Temperature

Displays the temperature of the refrigerant in the evaporator, if the

sensor is present.

Evaporator Small

Temperature Difference

Displays the difference between the Leaving Chilled Liquid

temperature and the Evaporator Refrigerant Temperature. The

Evaporator Refrigerant Temperature will be represented by the

Refrigerant Temperature sensor input if the sensor is present,

otherwise it will be represented by the Evaporator Saturation

Temperature.

YK-EP Style B Centrifugal Chiller

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды