York 160.87-OM1 Скачать руководство пользователя

Страница: 151 / 268

Table 145: Programmable

Button

Access level Description

Quick Ramp

Current

Threshold

Service

This setpoint sets the motor current threshold where the VSD speed

command ramp rate changes. At or below this threshold the speed

command ramp is 4X of standard control. Over this threshold, the

ramp rate is 2X of standard control until it hits the standard current

limiting over 80% FLA. Higher current thresholds can result in faster

pulldown times. However, setting this value too high can result in

slower pulldown times due to hitting the current limit sooner on

pulldown. (20% to 80% FLA; default 50%)

Quick

Pulldown

Setpoint

Offset

Service

This setpoint sets the Leaving Chilled Liquid Temperature at which

the control transitions from Quick Start mode to normal operation.

It is entered in the form of an offset above the active Leaving Chilled

Liquid Temperature (LCHLT) Setpoint. Once the Leaving Chilled

Liquid Temperature falls below the Active LCHLT Setpoint plus Quick

Pulldown Setpoint Offset, PRV (Quick Restart) and speed control

(Quick Restart and Quick Normal Start) revert to normal automatic

control. Lower values of this offset result in faster pulldown times

but can result in overshoot of the LCHLT Setpoint. Setting the value

to its minimum of 0 results in the fastest pulldown time but nearly

always results in setpoint overshoot. Depending upon how close the

Low Chilled Liquid Temperature shutdown threshold is to the LCHLT

Setpoint, this could result in a LOW CHILLED LIQUID TEMPERATURE

cycling shutdown. (0°F to 10°F; default 5°F).

The Leaving Chilled Liquid Temperature and setpoint is shown on

the QUICK START Screen for reference. This setpoint sets one of

the two setpoints that determine when the control transitions from

Quick Start mode to normal operation. The other is the Pulldown

Override Time below.

Quick Start

Mode

Admin

This setpoint is used to Enable and Disable the Quick Start feature.

It can only be Enabled when the Motor Drive Type Setpoint is set

to VSD or MVVSD and the Motor Communications Protocol is set to

Modbus.

The default is Disabled. Quick Start can only be enabled using an

ADMIN password. When logged in at ADMIN access level, a QUICK

START key will appear on the SETPOINTS Screen. Pressing this key

will navigate to the QUICK START Screen where this setpoint is used

to enable/disable the feature.

Quick Start can be Disabled when logged in at SERVICE access level.

However, once Disabled, it requires an ADMIN password to enable

it again, as explained above. Quick Start mode will be automatically

disabled when any of the following occur: The Motor Drive Type

is changed to something other than VSD or MVVSD, or the Motor

Communications Protocol is changed to YORK.

151

YK-EP Style B Centrifugal Chiller

Содержание 160.87-OM1













































































































































































































































































Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды

York 160.87-OM1, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 160.87-OM1

Отзывы:

Похожие инструкции для 160.87-OM1

Бренды по названию

Популярные бренды